Hello, I am currently using the nRF9151 LACA A1A SIP module for the development of NTN communication application terminals. In my hardware design scheme, the nRF9151 module...
Hi
We are using nRF5 SDK v14.1.0 and soft-device S132 v5.0.0 for our device which are already in production.
For function/feature improvement in this devices, we like...
Hi,
We are developing on nRF52832 with NCS v2.9.2 (Zephyr) on a custom PCB (LDO, no DCDC, 32 kHz RC).
On the same hardware, our nRF5 SDK firmware shows much lower average...
Dear Nordic Team
nRF54L15 is advertised as supporting BLE 6.0. our product is a type of charging case,I would like to know if we need to pass BLE 6.0 certification?
If...
We are trying to bring up a new run of an existing PCB design. No changes in the area of the processor, but a different assembly house. The first call inside ble_stack_init...
Hi Nordic team!
I haven't been able to implement the joiner functionality on a Thread network with nrf52840. I'm using the nRF52840-DK as the leader. For the DK, I follow...
I run a large research lab using hundreds of nRF52840 DKs. These boards are periodically rotated between active experiments and storage. Because boards are pulled from storage...
Hello:
I have detected a problem with a timer on my program.
I can solve it, but I would like to understand what is happening exactly.
My program starts to scan BLE signal...
I'm writing the client-side code for the Nordic DFU service and according to the spec, the DFU packet characteristic uses Write Without Request. Are there any examples of...
Hi,
I'm trying to implement a HID gamepad on nRF52832. Here is my situation:
nRF is receiving frame over UART from master uC every 15 ms. Frame is being converted and...
I was trying to track down high, approx. 6mA, processor current consumption and I have found high current consumption if the FPU executes a divide by 0. If I comment out the...
When I start the "ble-sniffer_win_1.0.1_1111_Sniffer.exe" program I get this screenshot:
The port was found correctly (COM4) but I see no devices found.
Am I missing...
Which is more lower power consumption,system off mode or system reset (according to nReset/SWDIO pin Lo) when we don't use nRF51822 for a long time ?
Our products have...
Hello,
I have this code
if (NRF_SUCCESS!=nrf_drv_twi_tx(&m_twi,devAddr,®Addr,1,true))
return false;
unsigned int err_code = nrf_drv_twi_tx(&m_twi,devAddr,data...
Hi.
I'm using PCA10028, SDK10.0.0 S130.
I think "ble_app_hrs_rscs_relay" provides Central function and Peripheral function.
So it should be advertising right after running...
My program doesn't use SoftDevice.
In Reference Manual 3.0 page 52: "A HFCLKSTOP task will stop the HFCLK oscillator. However the HFCLKSTOP task can only be sent after...
Hi,
I've looked at the example codes provided by Martin in these two topics for communicating to a MPU6050 through TWI:
1- devzone.nordicsemi.com/.../ (uses SDK 9)
...
When we add a uuid will follow the steps below
err_code = sd_ble_uuid_vs_add(&nus_base_uuid, &p_nus->uuid_type);
// Add the service.
err_code = sd_ble_gatts_service_add...
I was looking the way to set different tx power values and also figuring out a small bug in the interface when you switch among payload models and payload length is >1.
Bug...
nrfgo_error.docx
Using nRFgo Studio as the interface I try to download the file “set_in _test_mode.hex” and get the error above.
What are the proper steps to get DTM...
I am trying to reset and halt the target nRF51822 under SWD protocol.
Could someone point out the register to achieve the same? I looked up the reference manual but couldn...
