Hi, i have locked my beacon with the write_lock characteristic and now i want to unlock the beacon with the lock code which is hard coded in my code. but i was unable to do...
Hi,
I recently updated Nordic connect SDK and toolchain from v2.7.0 to v3.0.1. When compiling my application with activated CONFIG_BT_LL_SOFTDEVICE flag, I get this error...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
I have a USB HID device using the 'old' USB stack in Zephyr. I have configured the 'CONFIG_USB_DEVICE_REMOTE_WAKEUP'
1. I put the HOST to Suspend
2. The NRF52 USB goes...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hi,
What is the procedure and source code required to enable Device Firmware Update over BLE and USB. We are using nRF51822 chipset. Assume that our requirement will be...
Hello,
I am using a nRF51822 DK.
Actually I want to develpoe a product what can connect 3~10 slave(Low Battery device) by BLE.
And they have to reconnect fastly anytime...
A friend installed on two XP machines this software in this order..
Keil's mdk472.exe
Nordic's nrfgo_sdk_2.3.0_setup.exe
Nordic's nrfgostudio_installer_1_14_1...
I downloaded the nRF51SDK and followed the Quick Start guide in the Evaluation Kit Userguide (KEIL, Segger, etc)
But when I install nRF51 SDK v4.3, the installation failed...
Hi,
does anyone know if there is a document in which is explained, by Nordic, how to obtain a bluetooth certification using nRF51822 and S110 Stack ?
I know if a reference...
I have uploaded the following code, but I can not re-program the next.
#define AREF0 0
#define AIN3 2
#define AIN4 3
int main(void)
{
// Start 16 MHz crystal...
I'm looking best settings of fast connection to Android4.3
The time of advertise start to connection established average is about 7s
I think it is too slowly, may be My...
Hi
I write an application code to read and write the data from EEPROM, by using twi_hw_master.c.
its working fine. i able to read the data from eeprom what i have written...
Hi,
Let's say that you have a processor and a nRF51822 as a coprocessor. The first processor sends commands to the nRF51822 to drive it (init the stack, init the services...
Hi all
I can debug some example project with breakpoints likes blinky_example .
But in ble_app_hrs project, how can I set breakpoints and watch variable value with Keil...
Is there any limitation for number of advertised services?
ble_uuid_t adv_uuids [] =
{
...,
...,//more than 4
...,
};
advdata.uuids_complete.uuid_cnt = sizeof...
Here I´m again,
Maybe sound a little bit silly but I´m not able to find a way or a solution to make simply a Characteristic with more than one attribute. Something similar...
Folks,
Is there a document that describes the events generated by the S110 Soft Device and their interpretation? (Note: they're not listed in the S110 SoftDevice Spec v1...
