Hi,
I am currently testing the dect_shell example on two nRF9151 DKs and achieved a range of ~500m. I want to transition this setup into a multi-hop mesh network topology...
Hi: The device shows successful reconnection, but the mobile end is not connected.
And the connection information displayed on the device is (public), which is actually...
I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
I've had good luck running the examples such as the blinky and the basic BLE examples. Now, I'm trying to get the SPI Master example to run, but it does not seem to work out...
Hello Everyone,
As mentioned in nRF51-DK user guide, nRF51-DK has segger J-link debug out functionality. that means we can use this on board segger for downloading hex...
I have the nRF51822-DK and have been able to build and run the sample projects, e.g, ble_app_beacon.
I've just built a board using Taiyo Yuden's EYSFCNZXX module that's...
test the gpiote_example for timer0 in pca10003, the function is ok, LED blinking 200ms. but I change the timer0 to timer1 or timer2, the LED always on,and never blinking....
Hi! I use S130 on nRF51822 device.
After device is connected as peripheral I try to discover services using Master Control Panel but device disconnects. In Master Control...
I'm trying to start advertisement after establishing peripheral connection (on BLE_GAP_EVT_CONNECTED event) but called function sd_ble_gap_adv_start(...) returns NRF_ERROR_INVALID_STATE...
Hi
I'm working on a project to drive a DC motor, I really didn't find any example. I would like to know how can I program a pin in Keil, and I would be happy to have a...
Hello,
I am trying to get a lower connection interval from iOS. But the lowest connection interval I could get were 30ms.
Anyone has experience to achieve the connection...
Hi.
I find this code github.com/.../nrf51-dfu-single-bank-ble
I want to compile bootloader and download it on PCA10004.
I have KEIL 5.12 and the project file of the link...
Hi,
I want to create a service for test logger. Through this service i want to write n bytes at a time and after few delay want to write again some n bytes. These written...
I'm struggling to get started using Keil with an NRF51822 mounted on a custom board that I have cobbled together.
I have opened the blinky/pca10031 example as a starting...
Hello, I have two nRF24L01 devices that can already talk to each other on a custom address. When I try to talk to the nRF51822 from one of the nRF24L01 devices, I cannot get...
services.h
Hi,
I'm writing an interface for my nRF8001 and am a bit confused about the NB_SETUP_MESSAGES value. In my services.h file the value is 14 when it appears there...
