Windows x654 is OS
I have purchased the 2 boards nRF54L15-DK
I have not downloaded the correct nRF Connect for Desktop or the nRF Connect for VS Code
I have an older...
Hi,
I am currently testing the dect_shell example on two nRF9151 DKs and achieved a range of ~500m. I want to transition this setup into a multi-hop mesh network topology...
Hi: The device shows successful reconnection, but the mobile end is not connected.
And the connection information displayed on the device is (public), which is actually...
I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
Hi.
For my application, i want to do a battery saver profile.
I need to send one advertising package every 30second.
So now i do this by setting
#define ADV_TIMEOUT_IN_SECONDS...
Hello,
we have an application that involves 3 devices that comunicate over ANT. One central device beeing slave to the two other devices. All channels are configured with...
In ble_gap.h I noticed a parameter called BLE_GAP_ADV_INTERVAL_MIN, which determines the minimum gap between BLE advertisements. Current setting is 0x0020.
Currently in...
AN36 refers to the Send Update button on Master Control Panel(to toggle the LED). I can only see a "Write" and "Write Long". Am I doing something wrong, or does AN36 refer...
This may be the most commonly asked question but I'm new to this embedded devices.
I'm trying to develop a nRF51422 based sensor network which operates using CR2032 battery...
Is there a firmware I can download to have nRF51 Dongle working with ANTWARE II?
I plugged in nRF51 Dongle (PCA10031 V1.0.0 2014.30). I can see it in nRF Studio.
When...
Dear Sir,
I'm studying S120 and S130 soft device.
However, the document inside SDK dose not explain the detail of connection procedure.
I'm interest in the device how to...
I have one task to send image to nordic device(BLE device), But i am confuse to where to start,
Is it Possible to send image to Nordic device Using BLE?
Any guidance on...
Hi! I've never worked with bluetooth before. I am using a Blend micro arduino-based board to send to the computer some different values (for instance an array of 10 float...
Hi,
I have a question related to GATT Services in BLE, so not strictly a nrf51 question although it's related to one of the examples. The example for the (Human) Thermometer...
I have a BLE wearable (Pebble watch) that I wish to detect using the nrf51822 evaluation kit. I can use the Control Panel to see the pebble. I would like to be able to us...
When I put the ESB lib into my BLE Soft Device the MDK tell me that it have some error in it.
What's wrong in my project? if I need ESB+BLE what should I do?(NRF51822+SDK6...
So I installed the Master Control panel software, plugged in the PCA10000, whereupon I was advised to update the firmware in the PCA10000. The firmware update apparently failed...
Hi,
I am trying to get the s130 example to work on my PCA10028 board nRF51.
First I had to change the starting adresse from 0x1C000 to 0x1D000.
I guess that this is due...
