According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
I have found the bellowing code which was in s130/ble_gatts_struct_seriallization.c of nRF51_SDK_10.0.0 : ( ble_gatts_attr_md_enc)
/* serializer does not support attributes...
I have two device , one is Tx-Device the other is Rx-Device.
Tx-Device : Auto continued Send 4 bytes data to Rx-Device by Radio.
Rx-Device : Using Radio Interrupt receive...
First of all I'm a BLE novice, so sorry if I'm asking obvious questions. I've built a home project where a battery powered mcu listens for requests over wifi and drives a...
Hello.
I'm trying to do as follows: ONE button used either to wakeup or to put system to sleep. In general almost everything is working but I cannot find how to configure...
HI,ALL
as i known, the BLE key is a six digit pin.
and in the static void device_manager_init(bool erase_bonds) ,the statement shows below:
register_param.sec_param...
According to this post , and this GitHub source file , in the nRF51 chip's mbed implementation:
The ADC reference voltage is 1/3 power supply
read_u16() seems to...
HI,ALL
in the nRF5_SDK_11.0.0-2.alpha_bc3f6a0 , GATT Server Event IDs.
i do not find the read event.
All i found is the BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST .
Now...
Hi, all
Recently I use nrf51822 CEAA, WLCSP package to develop a project on UV (ultraviolet), the UV sensor must be exposed to the sunlight. When we take the product board...
I'm running the DFU example from the nRF5110.0.0 SDK. dfu_dual_bank_ble_s110_pca10028 on the DK and it works perfectly using Master Control Panel, but it does not work from...
I currently have a dualbank bootloader setup and I'm trying to change it to singlebank. If I burn the singlebank bootloader with the jlink it works fine, but if I use the...
Hello,
I modified ble_nus_c to manage multiple connections.
The first time (first client) i call sd_ble_uuid_vs_add in init, it returns OK. The second time ERR_NO_MEM...
both for APP_UART_FIFO_INIT and APP_UART_INIT i never receive APP_UART_DATA_READY
but at least i get APP_UART_DATA sometimes .
most of the times i get APP_UART_COMMUNICATION_ERROR...
I'm trying to monitor the time a signal is high/low on a GPIO. It seems to work alright with timers and PPI, but I wish there was a way to reset the timer upon capture.
...
Hi,
What is the largest possible value of "MAX_VAL" for application timer given below:
"#define APP_TIMER_PRESCALER 0"
"#define M_DELAY APP_TIMER_TICKS(MAX_VAL, APP_TIMER_PRESCALER...
Since UART-BLE is an emulation of UART on BLE, is there a need for physical wiring of the pins (RXD, TXD)? Assuming I'm not using RTS/CTS as I have disabled flow control,...
