Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
hi there!
i'm struggling with the problem about using i2c with IoT SDK.
my project is about transferring sensor data (i2c) through ipv6 over ble , so i used the IoT softdevice...
I'm considering purchasing a nrf51 sniffer USB dongle. I believe I can use this to sniff beacon packets and with wireshark view the packet internals, data, channel number...
Hi
I tried to flash the softdevice with nrfprog, but it does not work. Even with nRFgoStudio it does not work.But with IAR I can program an example of the SDK (without...
Hello, all
I have a problem with ble data exchanging.
I have programmed an application which controls servo motors through phone application.
At the connection, ble...
Hi,
I am trying to use the SAADC to periodically sample an input from AIN0 and send the resultant data over a BLE link to a phone. Going through the forums I saw that the...
Hi,
I am trying to debug the blinky example project on the nRF52 development kit.
I have followed the following tutorial: devzone.nordicsemi.com/.../
Building and flashing...
I'm in the process of designing a circuit that requires Bluetooth. So instead of having a separate chip for Bluetooth and processing, I decided to use a Nordic Semiconductor...
Classic C documentation issue. Are the values that are passed by pointer (p_peer_address and p_whitelist) to sd_ble_gap_adv_start() copied into that function, or do they need...
I'm trying to read the 32-bit value of TIMER1, but it seems the value I read is always 16-bit value. When I debug the value is never above 0xFFFF.
snippet from nrf_drv_config...
The peripheral is actually a dual-mode device, with BLE being a peripheral device.
I can connect to this device and discover the GATT services with the nRF Connect iPhone...
What is the minimum and max value that the NRF_RADIO->TXPOWER register can get set to? The datasheet it takes a signed 8 bit for the setting, but what happens if you set it...
Hello,
I am trying to read data from nRF51422 ADC using SDK51 PCA10028 board downloaded with S130. I tried one of existing ADC with Softdevice examples, it seems to work...
I have meander antenna design on my board with matching network(similar to PCA10031).
Since I don't have access to VNA or Spectrum Analyzer for tuning antenna, I am tuning...
I'm building some code off of the twi_master_using_app_twi example which is available in the SDK (v11.0.0).
The two peripherals I'm working on are an accelerometer (LIS3DH...
