Hi everyone, I have a custom board in nrf52833. Currently, the gpios on nrf52833 are gone, except for the NReset pin (P0.18). Can I configure the NReset GPIO as a GPIO I/O...
My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I am currently attempting to send HTTP requests (GET and POST) with my nRF9160 DK over an LTE connection. I have tried running the HTTP client sample code under zephyr/samples...
Hi,
Currently, we develop a prototype that needs to communicate with WuR; the FH101RF. Could you please tell me if it is possible to communicate with it? If not, can you...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hello, could you please provide me an working example of TCP socket communication using Thingy:91X by LTE-M/NB-IoT?
I haven't found any (only UDP and I need TCP).
Thank...
Hi,
I am using the nrf54l15 on a custom board in our current project and want to use it with DFU over BLE FOTA as well as TF-M.
I can compile the project just fine before...
I need to use Timer 0,1,and 2(I have only 3 timers 0-2 in nRF51822xxAA). This means, I cannot afford to let the BLE use a timer(I can certainly afford to give one RTC for...
Hi,
I'm trying to update attribute value and notify it to client using sd_ble_gatts_hvx() function:
memset(ms, 0, sizeof(params));
params.type=BLE_GATT_HVX_NOTIFICATION;...
When I use sd_ble_gatts_hvx() to send data to iOS and Android device I meet a problem:
Data send to iOS ok,but will return error 8 (invalid states) when send to Android...
Hi,
I am trying to use SPI to get data from a sensor. In nRF 5 SDK V11, I got it to work by setting the SS pin in the config struct of the initialization function.
...
I guess the answer is yes, because I know Characteristic Declaration (UUID 0x2803) has an unique handle for each characteristic.
Just wanted to confirm.
Its the first time I use simple_timer. I do not use the Softdevice. So I'm working with the peripeheral simple_timer example(SDK11).
I know from the app_timer, that every...
Hei!
I recently added WDT to my existing project. After that the normal behavior/sequence of code is not as it is supposed to. Strangely it works okay every other run now...
I just get DK P10040, I am using SDK_11.0.0_89a8197/s132_nrf52_2.0.1_softdevice.
I tried ble_app_uart, it works.
But I find a problem, I cannot set P0.09/10/12/13 high or...
I'm trying to compile nRF51 SDK 8.0.0 under Windows.
So for that purpose I'm going to components/toolchain/gcc and running 'make' there.
No targets specified and no makefile...
Hello,
I find in your source code contradictory values for the UART TX and RX characteristics.
E.g. have a look at nRF toolbox (both Android and IOS) definitions: github...
Hi all,
I am trying to implement DFU on my device with marginal success. Here are the steps that cause the issue:
Using nRFgo Studio: "Erase all", "Program Softdevice...
hi
I use S130 from nRF5_SDK_11.0.0_89a8197 as an ble central base on ble_app_uart_c example. when the ble_peripheral change the adv's content(means have data to send),the...
I have been able to follow the instructions in the nrf5 iot sdk to connect my nrf52 dk to a raspberry pi, however I am unsure why a connection must first be made before I...
Hi,
I'm using nrf52 with S132. I noticed high current draw after calling sd_ecb_block_encrypt() function.
After calling function consumption is 6mA and stays at a constant...