I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
in my tutorial I need to implement an I2C or TWI sensor on a peripheral BLE. In SoftDevice Software in Example-> Peripheral there are 2 methods 1) twi_sensor or 2) twi_master_with_twis_slave...
I used nRF Mesh app both iOS and Android versions to communicate with
nrf5_SDK_for_Mesh_v2.0.1_src\examples\light_switch\client
and
nrf5_SDK_for_Mesh_v2.0.1_src\examples...
The system consist of two nRF52832, one acting as SPIM and the other one as SPIS. I hace created a while loop always asking for certain amount of bytes but the MISO line on...
Hello, I am new to nRF micro-controllers and using Netbeans. I have cloned the repo of a project I would like to run, which builds successfully, and am getting the following...
Two questions. 1) What is the point of the watchdog ISR? In the Ambiq Apollo 2 microcontroller, the watchdog ISR fires and if the CPU doesn't pet the watchdog slightly after...
Hello I have problem with Mesh Serial Example and Interactive_pyaci, it works just in Debug-Mode. I use nRF52840, nRF5_SDK_15.0.0_a53641a, nrf5_SDK_for_Mesh_v2.0.1, Python3...
Hi I am trying to optimize my nrf51 app for low power. However I can just reach 0,500mA when just advertising (advertisement only is ok for me). Do you know or do you have...
I am trying to integrate the NFC read/write functions in my BLE application. I have used the writable_ndef_msg project functions to start with. The project on its own works...
Hello
For my final year project at Varsity I am creating my own smartwatch + edge computing IoT system. The watch and infrastructure needs to be as low-cost as possible...
Hi,
I am using a nRF52 DK board and programming in python.
After performing a successful DFU over BLE i want my Target device to be disconnected from the nRF board so...
thanks for the answer on the previous post.
What I came to know from our firmware engineer was that your initial version of the Android app could not support
1. multiple...
I want to know 2 things about the nRF Mesh app:
1) Is it possible for the Mesh app to provision non-proxy nodes via the proxy nodes?
2) I think it's possible to subscribe...
I have a project using FreeRTOS with Tickless idle enabled, SDK 11.0.0 alpha and the S132 soft device. Currently the project is consuming ~6.5mA average, ~5.2mA if advertising...
Hi There,
I very new to Nordic BLE application and was looking for method to combine ble_app_beacon and ble_app_blinky togather and having both switching and running at...
