Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Are there any good tools/apps to commission/provision an ble mesh application that is NLC compliant. Silvair is a great option, but is a closed ecosystem. We are looking for...
We are using the nRF5340 and our use case makes full use of all 4 shared peripherals for SPI and TWI as well as SPIM4. We want to add UART over USB and I was able to port...
Hello, we're currently developing BLE devices with PCA10040 and nRF Conenct SDK 2.9.0.
During a series of experiments, we found that with the same hardware and the same...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
When calling the bt_conn_le_create_synced function to create a connection to a peripheral, which is synced to the PAwR train, I get a CONNECTION FAILED TO BE ESTABLISHED ...
Hi
I am try to developing ble mesh gateway to connect and controll different nodes using nrf52840. Please give guidline to do this. I think proxy node is bridge of host...
Hello,
I am trying to use an sdcard with the nrf54l15 DK board with the 2.9.1 sdk. However I encounter "<err> fatfs: Storage init ERROR! error: -134" when calling the disk_access_init...
I have been working with 2.9.1 but went back to a project using 2.6.1 to flash a nrf5340dk and can still compile it, but now cannot flash the nrf5340dk. I am getting this...
Hi,
I am trying the system_off sample of Zephyr version 4.0.99: https://docs.zephyrproject.org/latest/samples/boards/nordic/system_off/README.html
The sample works...
Hi, I am using two nRF54L15 DKs running THroughput samples.
The result of coded s8 is 52kbps, which is close to the theory number.
When I change to S2 code, the result...
Hello,
I'm currently working with the channel_sounding_ras_initiator project on the nRF54L15 DK , using the nRF Connect SDK from the latest main branch on GitHub ( nrfconnect...
Can the NRF54L accept a CMOS output clock signal on XL1? The NRF52s could do this via clock source register settings but such a configuration is not listed in the NRF54 datasheet...
Hi,
I am trying to use nfc_t4t_lib and I have some issues because processing incoming data takes some time (around 100 ms) and therefore sending the response occurs late...
Hello, I have been going through the DFU and FOTA lesson in the Nordic intermediate course. I see that there is a FOTA support for a scenario in which we want to update a...
Hello!
Since we are moving from the prototype phase of our project to the pre-production phase, we have developed a custom board which utilizes the ISP2454, nRF54L15 SoC...
