Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi All, I have a question regarding modem DECT phy API. There is a function nrf_modem_dect_phy_event_handler_set(nrf_modem_dect_phy_event_handler_t handler). I'd like to know...
Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
nRF52832 custom board + NCS 3.0.1
We are using the Zephyr driver for LIS2DH sensor in "any motion" detection mode, which triggers an interrupt when acceleration exceeds...
Hello,
I'm evaluating the nPM1300 for a battery powered project. What is the quiescent current of the LDO? And is there an output current vs dropout chart?
Thanks
Hi, Using NCS 3.0.0 it would appear that the function sntp_simple_helper does not work with SYS_FOREVER_MS as a timeout value.
Problem: When we pass this value as a timeout...
I am trying to make a simple MAC-layer transceiver using Arduino environment. I have some code derived from this example: https://github.com/IoTS-P/nRF52-802154-Raw-Transmitter...
I'm trying to buy more data for my iBasis SIM cards that are provided with the nRF9160. I have 4 registered SIM cards and it was easy to buy more data through iBasis in the...
Hi,
I want BLE and ZIGBEE to be able to switch dynamically during running.Only one mode(BLE or ZIGBEE) is running at a time.If switching from zigbee to BLE, how do I turn...
I have implemented DFU functionality in my Bluetooth mesh project and used device A as the distributor and device B as the node to be updated. I have already configured both...
We have our firmware developed with ncs2.7.0 and everything works as expected. However, with a recent effort of moving to ncs2.9.1, the same project can be built but during...
When calling the bt_conn_le_create_synced function to create a connection to a peripheral, which is synced to the PAwR train, I get a CONNECTION FAILED TO BE ESTABLISHED ...
I have a BMD 350 nrf52832 module connected to nrf52DK board via P20 header. I am using nrf52DK to flash the firmware onto BMD350. my code works with nrf52DK and it logs onto...
We are trying to increase the TX output power on the nRF5340 when using Enhanced ShockBurst (ESB) . According to the product specification, the nRF5340 supports +3 dBm TX...
I am receiving packets in monitor mode on a nRF7002DK. I need some advice on how to interpret the signal value. From <modules/nrf_wifi/fw_if/umac_if/inc/system/fmac_structs...
