I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
What is the status of I2C pins and GPIO pins in the System OFF mode? Do they float once the SOC enters SYSTEM OFF mode? Here the accelerometer we are using consumes high current...
I tested Auto connect with NRF52832 UART APP(S132 softdevice), and nRF Master Control Panel APP.
I tested with samsung s3 neo and Moto G3 , but it is not working. In which...
I am currently using the watchdog in conjunction with RTX and a softdevice on the nrf51.
I am wondering if the default priority for the watchdog's interrupt works well in...
I am simulating button presses on a peripheral nRF51 device to determine average battery life. I send "button state" to central in a timer every 10s, with which I simulate...
Hi,
In my app , using SD130 , when i check the registers state while debuging i find that the RNB is powered on.
Do the SD130 power it on automatically? (because...
Hi All, We would like to use Alert Notification Service and UART service in our application. Here Our Peripheral will be Alert Notification client and UART Service server...
Hi, I have done the following:
Built a custom board with a brand new 128Kb nRF51822. On the board I only have the 16MHz xtal.
Routed out SWD IO/CLK and connected...
Apart from using nRF-Ready mother board, is there an option to program nRF2460. Probably through serial or third party SPI programmer? If yes, which one?
Is it possible to have one nRF2460 based transmitter to be received by multiple nRF2460 based receivers, or is the pairing one-to-one? In the datasheet, it says "The only...
Hi there,
I'm currently using the nRF UART app for iOS (v1.0.1), and I noticed it doesn't work the same as the Android app (v2). The key difference is the ability to select...
I am using external Crystal for my custom chip using nrf 51422 controller....
Just wanted to confirm is my setup for the external crystal (16 Mhz) is correct...
It is connected...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I'm using [nRF52_SDK_0.9.2] and original module. As a tool, I use the keil.
"NRF_POWER-> SYSTEMOFF = 1;" in the SDK example hrs also written, does not enter the system...
Respected SIR,
We procured nrf8002 BLE for our product. Currently we are in developing stage. We are using arm coertex M4-32bit based Teensy3.2 board as master. We havent...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
