Hello,
I'm looking for guidance and understanding of how to properly use the KMU and ITS for secure key storage of a key generated on device.
I see that typical ITS use...
Hello,
I'm currently using Visual Studio Code with the newest SDK, Toolchain and Plugin on MacOS and most of my applications are freestanding applications.
Now I want...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
Some questions in example ble_app_hids_keyboard/main.c
Why set the adv_params.timeout to zero in BLE_DIRECT_ADV (Line 779) ?
That will cause no BLE_GAP_EVT_TIMEOUT...
I just got a nRF51 and am having trouble getting started with it. I created a very simple program using the mbed compiler and produced a hex file which I now wish to flash...
Hello,
I see that the make files that have been included have provision to remove dead code from the projects to reduce code food print. This is accomplished using the...
HI folks,
I have checked the current consumption while connected on an average to be 325uA (with uC taking 4.5uA) so this mean almost 320uA being consumed by the nrf8001...
I have a general question about the RF frequency tolerance of Nordic devices in general. Is the following calculation correct?
Crystal spec = 16MHz, +/-50ppm tolerance...
Are there any plans to add boundary scan functionality to assist ICT testing? If not, are there any other hooks into the part that can be used to test during ICT?
Hello
I'm using a pstorage_register from pstorage.c to register two application storage blocks in flash memory. But I have situation that first module have 6 blocks of...
Hi,
are the GPIO pins broken out on the nRF51 Dongle configurable and can be used for SPI Slave tests? I have a running system powered by a ARM Cortex 4 (Teensy 3.1) and...
We have an early implementation of the v6 SDK DFU ported to support S310 on a handful of devices in the field and need to update them to a new bootloader and we'd like to...
Hi,
With the validation of the BLE V4.2 specification will Nordic be implementing the new features of the spec and if so do you have any idea of availability and dates. ...
Hardware: NFR51822_QFAAC0
Firmware: S110_7.0_SoftDevice
SDK: NRF518_6.0
Application: ble_app_hrs in NRF51822 S110 Examples
I start a timer to toggle led once per...
Hello Everyone,
I want to start working on nRF51822 development kit for my project. but as mentioned on this site : www.nordicsemi.com/.../nRF51822-Development-Kit
that...
Hello there,
I am using the experimental_ble_app_uart with S110 on nRF51-dk and receiving sensor data via 1MHz SPI every time the timer ticks = 100ms.
Data transfer displayed...
Hey,
I created a custom PCB with the nrf51822 that reads two sensors via TWI and transmits certain data over BLE. I can program the chip, print strings to the terminal...
