I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
we want to support the serial bootloader with SDK13, but find that the example is Experimental: Serial Secure DFU Bootloader, can we use it stably? the SDK14/15 don't Experimental...
I am using nrf52832_xxaa and SDK11.
Is there any formula that states the relation between the advertising & scanning parameters(advertising interval, scanning interval,...
I am trying to flash the program into my custom board. and i am successfully flash the program into custom board. I have flashed the blinky code in y custom board. it's works...
Hi everyone,
I would like to know in the ble_app_uart_pca10040 where the Bluetooth antenna is connected on pin planner to be able to change it.
Thanks you for helping...
Hello there,
I have a question related to the ADC of the nRF52832.
I am using it in single-ended mode, 10-bit resolution, 1/5 gain, internal reference 0.6V.
Thus...
Hello,
I am wondering what this "Low Power Event" is.
I am looking through the document but I can't find the place that explains this.
Can somebody point me to the place...
Hi, I followed the tutorial to Debug with Real Time Terminal on Keil.
fatal error: file sdk_config.h not found.
I have followed the tutorial as precisely as I can, maybe...
hi，there
I met an error in Nordic_HRM examples. The error code is GATT_CONN_TERMINATE_LOCAL_HOST.After the connection is established, you can see the service that has...
Good morning everyone,
it is the stupidest question ever, but I was unable to find an answer neither here nor on the segger forums or documentation.
This forum seems...
It's NRF52832 and NRF52810.
The BLE connection process is to establish a physical connection first and then discover the service to obtain the characteristic word information...
Hi,
For my application, I would like to have multiple watchdog timers. I am measuring several sensors (I want one short-term watchdog timer to be fed in this loop, pause...
I am new with nrf52 DK . I was trying to work with SPI code example given in the nordic example folder but its not working . I am trying to transfer the accellero/ gyro data...
I am using SDK 15.0 with the Nordic NRF52840 development board. I wrote my own custom bootloader using CDC ACM as the transport. I am using app_usbd_cdc_acm_read_any to read...
Hello All,
Is there any already available example of OLED display interfacing with nRF52DK, pca10040, SDK 14.1 in Segger Embedded studio?
I am working on a project...
