I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
I NRF51822 respectively, as master and slave, and bindings need to pair between the master and slave. I do not understand the contents of this, who can provide these routines...
Hi Team,
What are the chances of pkt loss in case of concurrent observer, advertiser role using S130? Application is like in observer mode device need to observe some activities...
We have an nRFgo nRF24LE1 32-pin 5*5mm Development kit.
How do we program this as a stand alone application without nRFgo Starter Kit Motherboard ?
Is there any tool or...
Seeing the Log on wireshark for Central and peripheral communication after connection.
Here i am bit confused that when Connection update request is send by Slave after...
Hi, I try to access Generic Access to get device name.
So, I modified "ble_bas_c.c - ble_bas_c_init()" like this.
bas_uuid.type = BLE_UUID_GAP_CHARACTERISTIC_DEVICE_NAME;...
Hi,
I want to find Bluetooth address of the Central Device which is running Master Control Panel Application....
but after succeful connection, each time I try to find...
I am using serial communication to have data from a sensor. That sensor only can support baud rate 115200 to communicate. Collecting data from that sensor I am trying to save...
Hello Everybody,
I have read these articles on the site : article_1 &
article_2
I need to do something like that, read around 8000 sample with sampling rate equals...
Hi,
I used the app of nordic , that puts the system off in order to measure the current at that mode.
the example i used is at this link . ( system-off-wakeup-on-gpio...
Hi
I'm very new and looking at the PTR5518 breakout board. The docs below specify some of the pins:
Are the pins EN , RX , TX , RTS etc. tied to P0.08, P0.09,...
Dear Sir/Madam,
I want to use the One channel of Timer 1 for PWM generation and other channel is used to measure the pulse width of input square wave.
For above i need...
When I try to step through my code, I get a wdt event firing. I have tried setting the behaviour to pause during debug and sleep
void wdt_init(void)
{
uint32_t operationStatus...
I would like to measure BER and PER on custom board by using sample project that is included SDK.
\examples\dtm\direct_test_mode\pca10028\s110
Could you please teach...
Hello,
I'm powering a Readbear BLE nano using a CR2450 coin cell battery. The firmware application is written using mbed. How can I measure the battery level of the CR2450...
hi,
can i use timer interrupt has more than 1ms period??
#define APP_TIMER_TICKS(MS, PRESCALER)
((uint32_t)ROUNDED_DIV((MS) * (uint64_t)APP_TIMER_CLOCK_FREQ, ((PRESCALER...
