I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi guys,
We have a device that is equipped with nRF7002 that is about to follow for certification. The laboratory sent us some questions due to the 5GHz band communication...
Hi there, I've been told on Reddit that I can post my design here to receive more relevant feedback.
I'm making a module with nRF54L15 with an external DC-DC regulator to...
I’m working on high-throughput data transmission using the nRF5340. My target is 80–100 kbps. However, I’m encountering issues on some phones during the transmission. The...
Hello,
I am using the NRF54L15 DK for development. I have configured the i2c with P1.12 as SCL and P1.14 as SDA.
below is my code in .overlay file
Below is the code...
Hello DevZone,
For some reason, some customers didn't want to add an external flash on their module. So I advice them to use MCUBoot SerialRecovry single bank DFU.
I modified...
Hello, I would like to ask if it is possible, to use the RTC RV-3028-C7 as the external crystal for low-power clock source as in the below design: Currently, we have on our...
This feature used to be helpful pre version 2.7 or so, but has persisted as an issue since then. All of the configs in any *.conf are all underlined and have this phrase when...
Hi,
Currently, we develop a prototype that needs to communicate with WuR; the FH101RF. Could you please tell me if it is possible to communicate with it? If not, can you...
Hi All, I encountered an issue while trying to use both Bluetooth and ESB in the same application. To clarify upfront: I am not using these protocols in parallel. Also, I...
NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
There appears to be a bug with commenting in prj.conf. If I do this:
# This is the appearance of the device from the BLE SIG Assigned Numbers List (384 is general remote...
Hi there,
I am currently trying to program a custom PCB equipped with the BMD-380 that has the nrf52480 inside. Sadly, I am now stuck for days with the same issue: It...
Hi,
I want to test the behavior of Enhanced Multi-Admin added in Matter 1.4.
Is it possible to verify this behavior using a Nordic DK board, sample code and a Raspberrypi...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
