I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
Ok, Here is complete rewrite of " https://devzone.nordicsemi.com/f/nordic-q-a/36589/connect-to-nrf52832-central-mode-from-android-phone-pheripheral/"
I would like to update...
Hi,
Currently, I use the sdk 12.3.0 on a PCA10028 EVK with the s130 softdevice.
For some reason, I want to change the default location of my application. By default, the...
Hi...,
i have measured round trip delay from client to server.
Now I want to measure total time required to send message from server to client and client acknowledges...
I did current measurement for NRF52840. For mesh light switch demo example measurement was 10 mA, and for Thread CoAP Examples current measurement was 0,6 mA. I don't understand...
Hi all,
I am developing an application for a product where power consumption is critical. The application is bundled with the Secure DFU bootloader. I noticed that the bootloader...
Hello,
I think the question may be more related on how Wireshark works but I plan to do the following:
* use the v2 sniffer firmware and the Nordic Wireshark plugin
...
When I migrated, the reference routine output PWM, but kept reporting errors. I have also changed the relevant definition, but I still can't. Has anyone met it? Thank you...
Hello,
We're evaluating the Laird BL654 using your nRF52840 (to be precise, we're using two DVK-BL654-1.0 development kits).We tried to use the 'blinky' examples (ble_app_blinky_c...
Hi everyone,
I am developing a remote controller using nRF52832 chip. My prototype is currently developed in PC10040 board. The IDE is Eclipse Oxygen, and the SDK is S132...
Hello, everyone~
I plan to use the Low Energy Secure Connection funtion with nRF51822. But when I build the lesc example in SDK 12.3.0 (ble_multirole_lesc), there's a error...
Using the sdk15 and softdevice 132 v6, I'm setting up an app to read and write to an SD card that uses SPI1 (SPI0 is used by a display). Everything is working great, except...
Hi,
What's is the max length for the payload data in "mqttsn_packet_sender_publish" method?
EDIT:
Redefining my question above: What's is the max length for the payload...
Hi Sir,
According the table 19.4.2 of 52832 datasheet (v1.4), there is a start up time (0.36 ms) for HXFO.
How do I measure the start up time of my 32M crystal?
If...
Hello,
While an attempt to develop solid security mode bulded around Root of Trust starting from RTL and Device root key we found that unfortunately, it is mentioned in...
I would like to detect if a reset happened due to a brownout or an actual power off.
I tired so far using the GPREGRET and RESETREAS registers. They are useful to detect...
