We have two organizations/projects in our nRF Cloud account:
Jackwoida 51789c46 Team (retain)
James_Eval (remove)
I am the account owner/administrator. The James_Eval...
i'm writing bare-metal code for the FLPR (which was loaded by a bare-metal launcher running on the M33)....
when my FLPR code "idles" using the WFI instruction, power consumptions...
I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
What's is the max length for the payload data in "mqttsn_packet_sender_publish" method?
EDIT:
Redefining my question above: What's is the max length for the payload...
Hi Sir,
According the table 19.4.2 of 52832 datasheet (v1.4), there is a start up time (0.36 ms) for HXFO.
How do I measure the start up time of my 32M crystal?
If...
Hello,
While an attempt to develop solid security mode bulded around Root of Trust starting from RTL and Device root key we found that unfortunately, it is mentioned in...
I would like to detect if a reset happened due to a brownout or an actual power off.
I tired so far using the GPREGRET and RESETREAS registers. They are useful to detect...
I have an app that works perfectly when run from the debugger, but not when started by HW reset. We use the serial port to communicate to a control processor (STM32) The Nordic...
Hi,
I was trying to test a slot circle antenna with nRF52832 which is well matched to 2.4G~2.48GHz, but it is circular polarized antenna with high directivity.
However...
Hi All!
I use nrf51822 with sd s110 to send data to android phone with sd_ble_gatts_hvx. If sd_ble_gatts_hvx returns NRF_SUCCESS then that packet get to TX buffer. I didn...
With nRF5 SDK v15, the code size became too large for the free version of UV5 , Is there a way to reduce the code size by reducing some array size or commenting something...
Hi There,
I'm stuck with Getting BLE uart working in another example.
I wasn't sure if converting the BLE Uart example into a central/peripheral application would be more...
Hi.
I want to read thingy's sensor data. I'm using nRF52840 DK.
I have tried using ble_app_multi_link_multi_role example, but there are only read button state.
How can...
Hello everyone !!!
I've recently started working with Segger Embedded studio for nfr52840. I want to add a new driver into an existing projects.Let's say GPIOTE
I...
Hello,
Recently i am working on UART application on nRF51822 based product.
In UART application code, there is no option to configure the modulation rate.
So, I would...
Dear friends,
if i adjust the tx power of nRF52832, e.g., by calling sd_ble_gap_tx_power_set(), which phase of the current will be affected in the pic bellow? just the phase...
I am struggling with getting a Secure UART(Serial) DFU operation to function correctly when I attempt to enter the bootloader with a call from my app. I am using the basic...
