Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Screenshot of what I'm doing:
So I reset the nRF8001, then try to initiate a transfer by pulling REQN low. However, nRF8001 never responds by pulling RDYN low. I have...
I'm using nRF5DK PCA10040.
And, working on nrf5_SDK_for_Mesh_v0.9.2-Alpha.
I need to enable both of Bluetooth mesh stack and BLE stack.
mesh stack for mesh communication...
I added uart service ( here and here )
and I think in part of ble everything goes well. I have blinking led1 and can see all my services.
Then I tried add uart part.
After...
I have a custom board that has a nRF52832 device (receiver).
I am scanning for remote beacons (also custom boards with nRF82832).
The result is that I obtain the MAC of...
Hi I use 4 characteristics in peripheral and central. When I write to one of the characteristics in the peripheral, I read it using sd_ble_gattc_read in the central. But,...
Hi,
SDK14.0
nRF52832
I am using the dfu\bootloader_secure_ble example as my starting point. My goal is to create a very simple bootloader (with none of the dfu stuff...
Hi
We are trying to use the uECC library file (micro_ecc_lib_nrf52.lib) with our project that is built in Kiel. We have followed the instructions found here using the open...
Hello,
I'm using SDK 132 (v5), kiel 5, SDK 14 and the nrf52 dev board.
I'd like my application to have multiple Offical Services (Heart rate, Humain temperature,...
Hi,
For my new project, I copied the linker script and Makefile from examples/ble_peripheral/ble_app_uart/pca10040/s132/armgcc to a folder and changed the SDK dir and project...
Hi All,
I have developed a device using the nRF51822, and the connection interval is set to ~1000ms.
When reading a characteristic from a Raspberry Pi, we are timing...
Any updates on this from anyone? Please advise
Hi,
The i2S microphone that I am using requires a over sampling rate fixed at 64 therefore the WS signal (LRCLK on nrf52...
Hi community, I'm running a 51802 on my custom board with no other parts on it, except for some buttons and leds directly connected to GPIO, and a DC/DC converter which feed...
The term 'slot' is used in the context of the Eddystone beacon specification.
I cannot find a definition of that word.
For example, the sample app from Nordic says ...
