Hello, I'm working on a prototype device based on the nRF9151 DK.
HW: nRF9151 DK, nRF9151 LACA A1A Tested with modem_shell sample app, NCS v3.4.0.
Symptom: on boot, "The...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
NCS: v3.4.0 Board: custom board based loosely on PAN1783 TF-M not used
Images: - App core: mcuboot, Firmware (main app) - Net core: b0n, ipc_radio
Summary of configuration...
Hi there,
I am starting with nrf52 and SDK 9.0.2 and am struggling with the SDK structure.
Can anyone please explain the difference between
components/libraries/uart...
Hello, I have tried to combine saadc with softdevice, but having errors during compiling. I have copied .c and .h files from saadc example to ble_hrs example, but having following...
Hi,
I have a specific application/product where in I am planning to use Nordic nRF52832.
-> There is a 9 Axis Inertial Measurement Unit (accel/gyro/magnetometer) connected...
Hi!
I have been trying for over a year to figure this out, but I am unable to, and I would hope it be pretty straight forward since OTA is already in the Nordit Master Control...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
I have a device (configured as a slave) which is connected to a relay to on/off a motor.
Now, I need to connect it to multiple masters (e.g., couple of smartphones) to remotely...
Hello Guys,
I need suggestion regarding the selection of nrf8001 ble module
Does it support OTA updates?
What is communication interface? is it SPI or conventional...
Hi,
I want to discovery all attribute UUIDs as Master Control panel application does. I use API function 'sd_ble_gattc_primary_services_discover' to discovery.
Exactly...
Hi:
I develop my project with gazell, Device can keep send to host,but host can't keep send to device(I'm not mean for host sent ack to device).
In my program, I use "nrf_gzll_add_packet_to_tx_fifo...
In the nRF52 reference design, not using the DC-DC converter would result in higher power consumption. By how much? Any documentation regarding the details. Thanks
Hi all,
I am new in nRF51822. Today I am doing experiment using GPIO and radio transmission.
I wrote a very simple code as below:
int main(void)
{
init_clock();...
Hi, I've got a serious problem in my project. Some of its features require hard timings. The usage time of these features is longer than the single timeslot and I must be...
Hello guys, I'm doing a hobby project and can't seem to get it working. Aim of the project is to transmit temperature values from a DS18B20 using an Arduino Uno and NRF24l01...
I'm experimenting problems with a nRF51822 custom board. Recently I managed to run the blinky sample project. Now I'm trying to test a BLE project, but I'm having problems...
Hey All,
I am currently trying to have a Analog Signal come in through P0.05 which then gets converted via the onboard ADC and send out a Service Characteristic. I am using...
