I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
We are using development kit for nRF52832 and trying to create the minimum current consumption that was stated in the datasheet which is 0.7uA while the system is off. However...
I did a search on Real-time debug, it's said for nRF52810, in Code generation, should set Debugging Level to Level 3, and Optimization Level to None Is that true for nRF52832...
Hi,
I've installed arm-gcc and the dev kit, I've tried several different versions.
I got it to compile the examples just fine. I can compile the example in examples...
Hi,
I tried to run the pca10056 ble_app_uart on a nrf52840 dongle (pca10059) after modifying the example as suggested here on the devzone. I had to define the rx,tx,ctx...
Hi !
I wrote a "central" device which works with multiple pheripherals.
Each pheripheral (Other NRF devices and also IOS) is going throw BLE_GAP_EVT_CONNECTED and when...
I am using pyserial on OSX as well as Ubuntu to send commands to the serial CLI via the JLink virtual com port for testing, and am occasionally experiencing lost/mutated characters...
Hi everyone. I am a beginner i really need help regarding an issue. I have two nrf52832 modules, on each of them i have a sensor from which i read some values. All i want...
While testing and debugging our current state of development, sometimes our devices go totally offline (thread visible via mqtt-sn last will, no ble advertising).
I found...
Hi,
Just to share my though here.
I think it is better way to decouple the BLE and application with dual core design.
It help to get rid of application latency due to...
Hello Everyone,
We have 2 devices. 1st device is flashed with the Eddystone example & sending TLM info. The 2nd device is flashed with a modified version of the ble_app_hrs_c...
Hi.
So I'm trying to configure my SW to use two uarts (as I've understood that uarte and uart are separate modules that can be used at the same time).
As the app_uart...
Dear nordic,
I implemented a uart in BLE application its works fine.
I need to reduce current for that i enable and disable uart but when i call function disabled or enabled...
hi team,
real quick; The accuracy internal reference (0.6V) used in the SAADC is specified in COMP section of the data manual as +/-3%. The gain error in the SAADC is...
