I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
I'm on SDK 15.2 and iOS 12 with nRF52832 on a custom board.
I've added the dfu service to my existing NUS/UART service. In the nRF connect app I can see both services and...
I have downloaded SDK software nRF5_SDK_15.2.0_9412b96. I am using segger studio as my IDE on windows.
I tried compiling the Example code for SAADC. There were no errors...
Hi, On SDK12.3 when using sd_flash_write at any memory location causes the device to halt and restart. On SDK11 I've been using flash_word_write and flash_page_erase using...
Hi I am using a nrf52832 board with a BMI160 sensor. I am trying to sample Accel and Gyro at 1600hz using a timer. The timer timeout is set at 20 ticks (32768/1600) @32768...
Dear Sir/Madam,
currently I am using SMK BLE module - BTS04, blank type (QDID 90744) and we have already acquired the Nordic Development Kit nRF52, Rev.1.2.4 date 2018.23...
morning guys ;
I wanna create a bluetooth pan using raspberry pi and beacon nrf51822 using ipv4 , i don't have problem with the raspebrry it works well and it shares the...
12.3 sdk
i have error when compile this project ''.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol SEGGER_RTT_printf (referred from main.o).'"
this error how...
Hi I trying to interface Accelerometer sensor LSM6DS3 to NRF52832 DK.
whether I need to change board configuration or any pin configuration.
Pin configuration that i have...
The reset button doesn't seem to work on two of my PCA10056 1.0.0 development kits, but works on two others, and works on some earlier versions.
I tested by running the...
It was working a few times, then suddenly I started to get these errors, which I only got previously when not running as root (perhaps because it did not have permission to...
Hi,
I am trying to process data from MPU9250 in MATLAB and I have converted " .mat " file to " .hex " file using Embedded Coder . Can someone tell me if that " .hex " file...
(1) I am using GNU C++ to develop my application with nRF5 SDK. I found the STATIC_ASSERT_SIMPLE and STATIC_ASSERT_MSG macros defined in app_util.h are not working with C...
When running the light_switch_provisioner example built on my machine, it crashes on an assert in entry_validation() in mesh_config.c:
app_error_weak.c, 95, Mesh assert...
