Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
I'm curious about the CPU lockup reset. We have a long term test with 9 units running identical firmware on identical hardware; line powered, running continuously for 6 months...
Hello,
I have a problem with turning on notification on a characteristic so I can start receiving data.
I am using a nRf51 dongle as a client device, using softdevice...
Hi, I would like to establish services with following security permissions in a Bluetooth 5 peripheral: Currently I use the NRF52-DK and SDK 15.2 Service A: Security level...
I'm trying to adapt the secure_bootloader example for our custom board with a nRF52832 QFAB with 32kB RAM and 256kB Flash, following the information in this thread:
https...
I'm building a project on top of cli examples:
<SDK>\examples\peripheral\cli
<SDK>\examples\ble_central_and_peripheral\experimental\ble_app_interactive
My goal is...
Hello
I need to setup the the PWM peripheral@ 8MHz with one selectet Channel in DMA mode. For development, I am using the NRF52840 Preview Dev Kit PCA10056 (Q1AAAA). I did...
I have one question, if Nordic can give some confirmation, that Nordic chips can be used together
with Murata XRCGB32M000F1H00R0.
Customer just asks for that I don’t...
Hi,
In my project NRF51422 need to communicate with two peripherals which are supporting only UART communication.
please help me if there is any possibility.
Thanks...
I'm use the app_button lib to deal with button event ,things go well, I assign the push ,release and long push event to button event .
But there came a situation,while the...
I have noticed that when I run in release mode, turn WDT on, write bonding info, clear bonding info, and reset, my application suddenly uses 2mA more and takes 5 minutes ...
Hi all:
My iOS app use iOSDFULibrary to update my ble.But when the device enter into DFU mode ,it disconnected for a while.
This is my log:
2018-11-27 21:00:11.122263...
Hi Nordic.
Now I am working on a BLE smart card and am adding an external power amplifier. For low power consumption, i decided to give power only when I want PCB doesn...
Hi,
I tried to use nRF52 evaluation kit to program my custom board for that I have used Debug port P19 in evaluation kit. It was working in the beginning but after sometime...
Hello,
I tried to follow the instructions in this tutorial: github.com/.../nRF52832-buttonless-dfu-development-tutorial
1) I flashed this file via nrfjprog: examples\dfu...
