Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
I am designing a custom PCB with NRF52832 IC. According to datsheet, required specification of inductor L1 are:3.9nH, 0402 package, 5% and a High-frequecy chip inductor...
Hello,
I did some power measurement on the nrf52 DK with the Nordic profiler kit and the result was way more than what we could expect from a nrf52 (about 1 mA). Even in...
I am working on the ANT connectivity for a product we've developed, called RunScribe [a shoe-worn running sensor], and am seeing some issues on Fenix 5 watches with our ANT...
Hi,
I'm trying to implement run the ESB and the BLE concurently using the timeslot API.
I started from this example : devzone.nordicsemi.com/.../
The problem is this example...
Hi,
I'm quite a beginner to this whole nrf52832 world and I'm trying to read some data from a flex sensor wired in series with another resistor connected to VCC now I understand...
In brief our problem with rfx2411n is that rfx begins to draw 200ma current without any reason. Rfx is powered down, powered from 3,0v. And suddenly something happens and...
I have a device that runs with nRF51 chip with the NRF UART Service (NUS).
I have a Raspberry Pi 3 and I want them to communicate.
The device requires an authentication...
My question is related to peripheral device only. I have implemented an auto connection interval negotiation algorithm which works as expected and negotiates connection interval...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Hello sir,
I have completed PCB design of custom nRF52832 board. Can i use following component instead of recommended part No in reference design. I have also mentioned...
Hello ,
I would like to design a custom board with nrf52832 IC and CP2102 for communication with PC serially. Unfortunately nrf52832 doesnot have Rx/Tx pins for interfacing...
Hi community,
for our application (nrf52832 / SDK 12.2) we need to store data received via BLE. The received data is a 25 kB binary blob which by design will be chopped...
Hi,
i am checking NRF52840 for USB behaviour.
I'm using example usbd_cdc_acm.
But USB receiving stucks after few bytes (between 0 and 50) and does not receives nothing...
i have nrf52 dk i run simple examle saadc from sdk 12.1.
now i want to get result.
i can't understand the code.
i start putty terminal adc event number and app info number...
