I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Trying to build the unmodified light_switch_client_nrf52832_xxAA_s132_6_0_0.emProject from a fresh download of the Mesh SDK.
SDK_ROOT set & successfully tested as instructed...
Hi Team,
This is more like a generic question.
I have 100 beacons and I want to test them all simultaneously kind of a bulk testing.
What are the possible candidates...
Hello,
I would like to use the hardware crypto engine that is a part of nRF52832 chipset. I understand that the access to it is restricted as SoftDevice uses it. I wonder...
I am running into these 3 errors while compiling my program. I tried fixing sdk_config.h.
.\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol app_uart_init (referred...
EDIT: I have added the battery data in percentage to scan response manufacturer specific data. Is that the only possible way?
Hello,
I am working on a beacon application...
Recently, I was trying to use the button to select the specific actions.
Actually, the program is built successfully and it can show the "UART Start!" via serial port, but...
Hi everybody,
I am trying to read a 1024 bytes FIFO buffer from an IMU (Bosh BMI160) using the SPI master driver on nrf52832 and sdk 12.2.
I know others had the same...
Hello,
I have developed an SPIS interface on a custom board using the nRF51. I also implemented an SPI interface on a nRF51-DK board and have had the two boards talking...
Hi,
We are using BMD340 in our project. In our application we need a storage medium for the storing of data. Since our application is an embedded application, we find eMMC...
I am using nRF-Sniffer-v2.0.0.2 beta as seen here: https://www.nordicsemi.com/eng/nordic/Products/nRF-Sniffer/nRF-Sniffer-v2/65225 on a nRF52840 DK.
Wireshark Version: 2...
Hello guys,
I'm having problems with communication between a dwm1001 module (from Decawave) which is a nrf52832 board, and my Raspberry 3 Pi model B.
I have connected...
Hi
According to nRF52840 Product Specification, the SPI master data rate can be set in the SPI frequency register. The configurable values are listed there. Is it possible...
Hello everyone,
Maybe it is a stupid question but I am completely lost,
I have a stm32f103c8tb that I have to use for programming a nrf51822, the thing is I have absolutely...
Hello,
I am developing a firmware to count pulses through a GPIO and store the sum of these pulses in a memory until there is pairing with the BLE.
After pairing, the sum...
