I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I have SD and BL secure flashed to the device, and now trying to get the second part of buttonless_dfu + app with settings flashed next. After flashing the second part, DfuTarg...
I'm attempting to optimize our application for battery life on the nrf52832.
If I execute a floating point calculation to rescale RGB to PWM, I start drawing 6.2mA, eliminating...
Dear all,
We are programming the FICR and have found very little documentation on the random number generator fields: - TRNG90B.BYTES - TRNG90B.RCCUTOFF - TRNG90B.APCUTOFF...
Hi
I have followed this example: https://github.com/bjornspockeli/custom_ble_service_example through to the end, but am now having issues with some intermittent behaviour...
I need to transmit and receive beacons using nRF51 DK. I saw a few examples in the SDK ble_beacons where we use the app, but I need code to transmit and receive both using...
I am trying to send 'h' or the number 1 using vendor defined page (custom HID descriptor). How do I do it?
NOTE: I have worked with hid mouse & keyboard examples and also...
Hi,
I am trying to make a network of four Nordic Thingy: 52 IoT Sensor Kits by using the nRF52 DK to program them. Then, the readings for the 4 senors should be displayed...
Greetings friends,
I'm having some trouble figuring out how to use the the sdk for developing a beacon central.
What I've got so far is: I used the BLE Central for UART...
Dear Sir/Madam I am currently designing a IOT board using nRF5284 as the main controller IC The board is battery powered and is charged using USB. Data can also be transferred...
We're seeing an issue where a dfu package containing SD+BL+Apps gets stuck on iOS nrfToolbox during DFU process after it updated the first part 1/2, which is BL+SD. The same...
Dear Nordic Team
I am developing a BLE device using the following resources:
- Microcontroller: nRF52832
- Softdevice s132
- Peer Manager is used for whitelist...
Hello,
I have developing one project in that i am using nRF52832 and SD 15.0. Here is the current application developing:
There are 3 ble app_blinky(ble peripheral)...
what do i need to modify in an application to send that application over mesh? Lets say i wan to send blinky example over mesh to all other nodes, what i need to change in...
I am using the mesh SDK 2.1.1 and have one node that uses the serial API. That node sends mesh packets to the network via the PacketSend serial opcode. This command uses an...
