Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
I have a nRF24LU1 USB device that I want to configure to make communicate with a nRF24L01 device on an Arduino Uno. I tried to install nRF Go Studio and J-Link Segger driver...
Can anyone tell me whether it's possible, within the SDK (or otherwise!) to create a grouping of GPIO pins? Essentially, a design change means that we want to combine what...
Does anyone happen to have 3D models of the PCA10040 and PCA10056? I found the Altium files, but, being an Eagle user (and not having an Altium license), I was wondering if...
Hello,
I'm using nRF52 SDK12.2 "ble_app_uart_c" project as a "Central", and the target device is the "Peripheral."
Test Steps:
Using putty sending message(with...
How can i initialise all four channel of pwm1 using pwm library.
i need to initialise one channel for one purpose and other channel for different purpose.
whenever i am...
Hi,
I just tried the example from
github.com/.../nrf52-mpu-easydma-using-gpiote-and-registers
And they are working like a charm. Now I want to change the example...
In the on_ble_evt(ble_evt_t*) function from the ble_app_template, I added a case of 'BLE_GATTS_EVT_WRITE'. In it has the following code:
case BLE_GATTS_EVT_WRITE:
{ ...
I have a hard time figuring out what some of the constants in nrf_mesh_config_node_app.h for my Bluetooth Mesh application should be set as.
Instead of writing a question...
Hello,
I'm working with ANT+ hrm profile and the relative Nordic's library, but I find out that there are missing pages. Infact I have only pages from 0 to 4. How can I add...
Hi,
I have taken the BLE Central Example code (ble_app_uart_c)in one nRF51822 hardware and in the other nRF51822 hardware, I have taken the BLE Peripheral Example(ble_app_uart...
Hello dear Nordic Semiconductor!!! I took your wonderful Thingy:52 everything was great until I wanted to build a project based on your Thingy: 52-SDK. I have nrf52840 pdk...
hi, i am having a doubt. now my nrf 52840 is acting as a peripheral. it is advertising some packets and my mobile is acting as a central and receiving the advertising packets...
Hi there,
First: I’m a newby, just did some things with Arduino to control some LEDs etc but not much more before.
What’s my plan: I actually ‘ld lik to control some...
I am new to BLE development and have started by installing SEGGER Embedded Studio
Release 3.30 and have a J-LINK edu usb device and a Core51822 board from Wavetek.
I understand...
