I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hello Nordic team
I am working on ble_app_buttonless_dfu example code and implemented accelerometer code via TWI0. And Accelerometer INT pin connected on GPIO via gpiote...
I am looking to develop a number of Zigbee compatible devices for home automation. Can you tell me if the nRF52840DK and dongle (no debugging using the dongle I understand...
Hi all,
After I combile light switch example and remote example for my client and server board . Function Remote run fine . But when I push button for send unicast message...
Hi. I try to run example Light Switch Demo.
I use: Mesh SDK v.2.2.0. NRF SDK v 15.0.0. Softdevice: s132_nrf52_6.0.0.
I see that relayed messages have maximum TTL = 4,...
Hi, I already have device that plays audio from sd card. New feature is needed that user can send MP3 file to device from mobile phone that will be stored in sd card and then...
below is a little part of code copied from nrf5_SDK_for_Mesh_v2.2.0_src:
***********************************************************************************************...
Hi team,
I am integrating bmp180 and mpu6050 into a beacon code.While integrating,I am getting the following error
"NRF_ERROR_MODULE_ALREADY_INITIALIZED".
Please help...
SDK14.2
Segger Embedded Studio
nRF52 development board
According to this post https://devzone.nordicsemi.com/f/nordic-q-a/20556/how-does-the-saadc-scan-mode-use-the...
Hi All,
Currently i am working on Zephyr RTOS as a target of PCA10040 DK.I have been compiling and executing a simple "Hello World " example.
While doing cross compilation...
Hello,
I have use the BLE Multi-link Example as a central. For the priripheral I have use BLE Blinky Application and UART/Serial Port Emulation over BLE ( <InstallFolder...
Examples in SDK15 use the Observer pattern to handle BLE events (using the macro NRF_SDH_BLE_OBSERVER). AFAIK, the registered handler runs in some IRQ context, typically higher...
Hello Nordic team
I am working on nRF52832 DK, SDKv15.2.
My question is how we can send and receive more than 100 bytes of data? I know nus services doing it. Also how...
Hello,
On one of our custom board with nrf52832, after programming it like 3-4 times it stopped responding on the nrfgostudio as in it was showing no device detected,...
Hello,
Now i use SDK15.0 and NRF52832 to make a BLE scanner.
I want to scan advertisers every 5s , scan window and scan interval are equal(max=0x3FFF). Also,they are all...
