If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hello!
Does anyone know of a library for the I2C LCD 16x2 display? I found the library by lovee, https://devzone.nordicsemi.com/f/nordic-q-a/23401/nrf52832-connect-with...
Not really sure where the problem is here, my guess is in the code... I just recently saw this: https://www.avrfreaks.net/comment/1342846#comment-1342846
Although my issue...
I'm able to successfully use peripheral/uart example to read the data from GPS module. I achieved the same by setting baud rate to 4800, and connecting rx and tx of GPS to...
Hi,
Question about FOTA (firmaware upgrade over the air).
I know that nrf52832 has 512 kB of flash, and the ble stack( softdevice ) has 136 kB , and the bootloader has...
Hi,
I put my NRF52 to sleep (POWER OFF mode) and configure it to wake on GPIO port event like so:
This GPIO is set up on a reed switch. Occasionally, the NRF52 will...
Hi
I found a strange issue on nrf52832. And I use nRF5-SDK-v13.1.0 .
When I assignment P0.7->SCL & P0.6->SDA, the twi function not working. But I change the assignment...
Today I read about the new nrf52810 and I want to know about its main differences with the nrf52832.
I see a lower power consumption for the 52810 vs 52832 and no NFC on...
Hi
Currently I try to migrate my software project (with SDK14.2, S132 (5.0.0), arm-gcc toolchain ) from nRF52832 to nRF52810 (with SDK14.2, S112 (5.1.0), arm-gcc toolchain...
Hello everyone, I am a beginner in the use of Nordic Thingy: 52. I would like some help trying to reprogram the Nordic Thingy module. After a programming error of the Thingy...
HI,
I am unable to communicate between a SDK 8.0 based nRF51822 sender and SDK 14 based NRF52832 receiver.
The data rate of the SDK 8.0 sender is 250 KBits/sec, whereas...
Hi,
Can someone help me with question on SPI?
What is the difference between SPIM and SPI? They seem to have different clocks
Also in the SPIM section, the frequency...
hi,
I need to know how to use "power on reset". From the reference document, I can understand BOR and POFWARN. But the POWER ON RESET, I could not get any idea.
1. POR...
i have project with nRf51822 and uart. i use uart fifo in Uart_app_ble example sdk11. now i need disable or enable Rx, TX.i tried this function :
NRF_UART0->TASKS_STARTRX...
Hi,
Has anyone successfully used semaphores/mutex implementations of FreeRTOS?
The code I am working on is based on the FreeRTOS HRS SDK example. I am looking to add a...
Trying to compile using the on-line Mbed compiler. I keep getting cannot find "nrf.perhiperals.h", and I cannot locate it either.
Possible someone can point me in the right...
Hello.
I'm using Tielen Marjle STM32 library for nrf24l01+ ( https://stm32f4-discovery.net/2014/06/library-17-nrf24l01-stm32f4xx/ ) which worked great till now, when I...
