Hello,
Overview:
Currently we are using nRF9160 we are using mbedtls library for generating EC key based certificates (self-signed and CSR). Our code is built with TFM...
Hello, I wanted to update my project (Custom board using the nRF54L15 ) to the v3.3.0 SDK since this fixed a BLE bug with the v3.0.1. version. To my knowledge I did not change...
Hi,
nRF9151 + Kyocera AVX P822601 internal SMT antenna: 8 dB RSRP loss vs external antenna — possible PCB layout issue?
Test Results
Test 1 — Out of Faraday cage, internal...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hello,
We are currently evaluating BLE Gateway (CIS, BIS) development using the nRF5340 Audio DK.
We would like to ask whether bidirectional CIS streaming is officially...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
This is kind of a follow-on to the original question here: devzone.nordicsemi.com/.../
I notice that the nRF52840 PDK dev boards need to be closer at the beginning of the...
Hi!
I am sending the battery status every 1sec from nRF52840 peripheral device and receiving it on nRF5240 central device. (verified the battery status working through...
Hi,
I am unable to read values from ADC pins, usiing nrf51822 nordic bt module, s130 softdevice.
Things I dont know:
Connecting to ADC pins
readings from the pins...
Hi,
If I set the tx buffer to 0 before and transaction, I expect the spi slave register's AMOUNTTX to be 0 when the transfer complete. But intstead, the AMOUNTTX always...
I'm working with a sensor that communicates over spi, but it uses a single wire for miso and miso. Is there any alternative to just bitbaning the protocol? Specific sensor...
Hello.
we are using the nrf51822 and doing the approval of the radio transmitting equipment model.They refer the modulation mode,as the picture:
I am asking:1、can the modulation...
I'm working on a central device. I'm using 52832, SDK11, SD2.0.0
I accidentally used a peripheral device that doesn't have the right service UUID that my central device...
I'm using nrf_delay_ms to trigger a series of beeps though a speaker using PWM, but I seem to have intermittent problems with this when the device is connected.
Basically...
I am trying to get fstorage to work, but I seem to miss some of the symbols needed: "error: 'NRF_EVT_FLASH_OPERATION_SUCCESS' undeclared". These are declared in softdevice...
Hi all,
I am using a BLE nano 2, which is based on the nRF52832. I am trying to measure small capacities of a few pF with this method:
wordpress.codewrite.co.uk/.../...
I want to connect a central and peripheral and only have ble on when the peripheral senses a certain event that exceeds a threshold. Do the devices need to connect on startup...
Hi Nordic,
I’m H/W engineer, dedicated in development of radio circuit. I ask the question because we’d like propose your Nordice nRF52840 to our customer when replying...
I am developing an application which uses 2 nrf52 running sdk 12.3 and softdevice 132 V3.
The central device appears to be saving and whitelisting the two peers, but it...
Hello!
We designed and manufactured board with nRF52832_QFAA. The NFC pins was configured as IO and connected to sensors. The problem is that we see that those pins get...
