I have tried several code samples: nrf/samples/bluetooth/peripheral_uart and nrf/samples/openthread/cli. If I set hw-flow-control in zephyr/boards/nordic/nrf9160dk/nrf9160dk_nrf52840...
We recently encountered an issue with incompatible image partitions being pushed to in-field devices causing soft bricking. refer to this ticket for more information
Problem...
Page 399 of nRF54L15/nRF54L10/nRF54L05 Datasheet v1.0 shows:
CLK = PCLK32M/(2*PRESCALER)
but this formula does not match the values in the examples in Table 46.
I CAN...
Hello Nordic Team,
I am currently working with the nRF52832 on a custom board using nRF Connect SDK v2.9.0. I am implementing OTA DFU using Sysbuild and MCUboot with an...
Hi Team,
I am working on OTA using an external Winbond flash IC (W25Q64) with the nRF52832 controller in NCS SDK version 2.9.2. I have completed all the required configurations...
Hi team,
We are going to kickoff a new project of 2-mic AI recording pen. Good to see we got a very high performance for 54LM20B with DSP/NPU, which might be a very good...
Hello,
We are currently developing a Zigbee product using nRF Connect SDK v2.8.0 . While reviewing the release notes for NCS v2.9.0 , we noticed two critical bug fixes related...
hello
In proprietary model of nrf51822，I doubt that the RSSI is not accurate in my testing environment，so i want to calibrate the RSSI info by using R&S SMU200A，can anybody...
Hello,
in the nrf52832 PS I've stumbled over the "EasyDMA array list mode". From the description, I'm unable to understand, how this works and what I can archive with this...
I have a custom board that has an MPU9250 attached as a SPI device. The MPU can generate data ready interrupts. I have set the MPU to generate data ready 4x per second which...
Where can I find documentation for using EasyDMA list mode on SPIM?
I've got nrf51822.
All I can find is this nrf52 documentation , which seems incomplete.
Is there...
I'm new to Gazell, so please excuse the simplicity of my question, but I just seem to be missing something.
I have an application where I will be using one host with two...
Hi
We are about to submit our system for BLE testing. We have been asked for RF-PHY:P9:1 RF-PHY:P9:2 RF-PHY:P10:1 values
RF-PHY:P9:1 Maximum TX packet length (MAX_TX_LENGTH...
Hello Nordic Team,
After setting connection parameters in accordance with Apple BLE design guidelines the BLE throughput has been significantly decreased.
My parameters...
Hello,
If I use the nRF51822 with 128KB ROM and I connect to a external flash via SPI.
The SoftDevice and bootloader are stored in the internal 128K ROM.
Is it possible...
Using GATT characteristic writes to transfer data is slow.Is there a cleaner and/or faster way to do faster OTA upgrade?
Also I wanted to upgrade firmware without affecting...
I have set up a 6lowpan test environment and could control the led3 and led4. could u please provide me with a code to read value at p0.01. i want to connect a temperature...
I directly connect GPIO pin with 24ohm resistor as follows.
And I set GPIO pin as high drive,
NRF_GPIO->PIN_CNF[MY_PIN_NO] |=
(GPIO_PIN_CNF_DRIVE_H0H1 << GPIO_PIN_CNF_DRIVE_Pos...
hello ,i use SDK9.0 ANCS project.when I paired it ,it can work normal. it can recive QQ,wechat,message and so on. but when I paired many times, it will be SystemReset.
...
Hi
I am trying to make an activity tracker with very low power conumption with the nrf52. The Idea is to count interrupts from an accelerometer thtat are generated if the...
