hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
At the bottom of page 15 in nRF52832 Product Specification v1.4 the following reference is printed:
[1] See GPIO located near the radio on page 17 for more information....
Hi,
If event is not handled (or handled but EVENT register not cleared), will it go above 1 or is it binary?
In other words, can the value be used to detected missed...
I am attempting to port code from sdk 11 to 15. Some of the code is __older__ and in need of updating. A line which runs during the application init calls the sd_ble_version_get...
Hi!
I have added programs for register writing to SPI programs and using SDK14.0.0
I am using the nrf_drv_spi_transfer function to transfer three data.
but when confirming...
Hi,
I am using nRF5_SDK_15.2.0_9412b96 and Segger IDE.
I have written to echo every data received from UART.
I have a variable UART_Data to store data received from...
Hi,
I am using nRF5_SDK_15.2.0_9412b96 and Segger IDE.
I have written to echo every data received from UART.
I have a variable UART_Data to store data received from...
Hi!!
I am now using SDK 14.0.0. and I have added UART functionality to the SPI program().
I could confirmed that SPI and UART can transmit data separately.
However,...
Hello,
I am trying to modify the ble_app_uart code so that my peripheral can send data automatically to the central, which in turn can print it on a computer through UART...
My application is a BLE peripheral and will only allow a single connection to a BLE central. Hardware will be nRF52832. My test application was based on a Nordic example that...
Hello,
I am working on Bluetooth Mesh authentication. I wonder if you have more details about Input OOB . I am trying to input a number from nRF Mesh app to send it to the...
I need to confirm before buying, whether the nRF52840 chip and the nRF52840 development board can be used to develop a Zigbee Mesh.
Also whether "nRF5 SDK for Thread and...
I need to do pairing between the two 51822 modules. All the information I find is paired with the slave and the mobile phone. There is no host matching process demo or learning...
Hi
I'd like to create a firmware that supports multiple Nordic boards as Hardware (as the nRFConnect Firmware does). To do that I have to configure the peripherals according...
