Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
I'm developing a central providing NUS client service to multiple concurrent peripherals.
I use nRF52832 DK and SDK14.0, s132_nrf52_5.0.0.
I Want that NUS central can...
Hi,
I am working on another project.
I want to make BLE and USB BULK communication operate at the same time.
My development environment is Keil,
It uses nRF52840 and...
According to the point above
link text
i bought the thingy but i did'nt think about the jlink ..
you can add me to the advent calendar ;-> for a nRF52 DK because...
I understand that the connection parameters viz. connection interval, connection supervision timeout and slave latency are negotiated between the BLE Central and BLE Peripheral...
We currently have a SPI interface between MSP and the Nordic nRF52840. In the DTM documentation it indicates UART is used to command the tests. Is it possible to do this using...
Hi,
I have 5 nrf52832 and nrf52851 beacon boards. All nRFs working in the beacon mode. They all in the same room. I tring to get a list of the active beacons the module...
Started out with the ble_nus-exmple. Added logging of a sensor to flash, and got it to work in SDK11, even without using the sd_flash*-routines, but writing/erasing directly...
I would like to perform an OTA on the DWM1001 board which has a nrf52832.Where can i get the details an the range that can be achieved with employing ANT.Are there any test...
I am following Tutorial 7 on "Development with GCC and Eclipse" and I am working in the Windows 8.1. I have followed instructions from the tutorial for installing the arm...
hi,
i am using a nRF5240 DK for receiving multiple services and characteristics data from Nordic_thingy_52,to receive and print this data on UART i used sdk 14.2.0's "ble_app_blinkey_c...
Hi there~. I was working on a BLE RC car (BLE peripheral) using Nordic's nRF52832-QFAA MCU , Nordic's UART Service for motor control, and Battery Service (BAS) for battery...
Hello.
The development environment is as follows :
OS : Windows 7 Pro 64bit
IDE : Keil uVision V5.24.1
Python : 2.7
SDK Version : nRF5_SDK_14.0.0
DK : PCA10040...
I want nrf51822 to switch between 2 different advertising timeout. One will set advertising timeout with 20s, another will keep advertising.
Currently, I use following...
I have a server running on my Android phone. I looked at the service UUID encoded in the advert packet using and Wire-shark and confirmed my app is broadcasting packets. ...
