void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
I had the following setup, two app_timers triggering blocking SAADC reads in the callback functions
app_timer 1000ms triggering 1 Blocking SAADC read (For battery service...
Hello,
I use sdk 8.0.0 and s110. I read this blog
And I did not understand some terms;
Application processing(for example 2ms each adv interval)
Number of packets...
Hi,
I am using the nRF51 Dongle (PCA10031, V 1.1.0) and pc_ble_driver.py to create a custom script for testing purposes. But there seems to be a maximum limit for the measured...
I met a problem when delete bonding information on android central, i actually can't connect to the nrf52832 peripheral again, until i totally clear it's peer list and bond...
Hi all,
I am trying to control a speaker using the i2s output of the nrf52832 mapped into a TAS2505 from TI. I am able to play sounds in the speaker but my issue is that...
I am trying to use the eddystone example I found in the ble_prepheral/ble_app_eddystone/pca10040 folder in SDK14.2 with my nRF52832 development board but I get the following...
i found this link on nordic website to learn ARM with Nordic SOC.
www.nordicsemi.com/.../Nordic-ARM-Lab-in-a-Box-University-Program
Do you know where is the link for...
Hi,
I am able to program a SparkFun nRF52 breakout board via nrf52 Dev Kit using Segger Embedded Studio. However, I am not able to achieve the same results using nrfjprog...
I am facing some issue while writing to i2c. On first i2c write , device is working but after that when i tries to write anything, code is stucking in loop.
void sensor_sleep_mode...
Hi,
I'm trying to port my project from SDk12.1 to SDK14.0, I've got everything working fine except the DFU process. The main issue is that we've got some devices distributed...
Hello,
I am designing a custom board with NRF52832 IC. I followed all PCB consideration suggested by Nordic.
This blog suggests, If using a PCB antenna, the matching network...
This question is similar to this thread:
devzone.nordicsemi.com/.../
However it was framed differently and didn't really clear anything up for me.
Say my application...
Hello,
I have an application that has to be ported to the newer Softdevice version. I've already ported my application to the SDK 13 and tested it with the new Softdevice...
