I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I have followed this posting by Hung Bui , with light_switch_proxy_server being combined with the ble_uart.
I am using: nrf52 dk, Mesh SDKv2.0.1, nrf5_sdk_15.2.0.
By commenting...
Hi,
Errata 202 limits the use of vdd as a power source to external components and I, therefore, would like to use a GPIO instead.
My question: is there a need to use a...
Hi,
In my project I am using SDK 14.2 with S332.
I need to change the data in the manufacturer part of the advertisement packet once per second (nearly, timing is not...
Hi,
I have a strange issue. I am reading values from an accelerometer. The read values go into an array which is uint8 and 7 bytes long.
The values are read ok and they...
Hello everyone,
My usb connector is dead on my nrf51 dk, do you know if it is possible to program it without using the usb connector, maybe by using a USB serial port adapter...
Hi!
Does latest NRFUTIL 4.0.0 include mesh update option?
I saw in branch dfu_mesh on pc-nrfutil github that this branch was last updated on 16.12.2016 (nrfutil 0.3) and...
In my project LPN node need to communicate with more than one friend node.
Is it possible to make multiple friend establishments by single LPN node or is it something like...
Hi all,
I started a project on nRF52840 dongle with Segger IDE. I used SDK15.2 given by Nordic and my goal is to develop a program that permits to communicate between...
Hi,
Noted that nRF mesh app needs GATT bearer to provision a mesh device. I'm using 2 nRF52 DK boards, provisioning is fine, set the keys, subscription lists, etc, everything...
Hello, First of, I'm developing with eclipse an application based on the freertos example of the SDK 15.0 with softdevice S132 v6.0.0. My problem is that the nRF52 sometimes...
Hi. I have the latest topology monitor downloaded from the home page. It seems to have a problem. Every time i try to run it from my windows 10 machine (32 bit), it gives...
nRF TTM win32-x64 will not run on my PC. I use Windows 10 and am trying to run the executable but i keep getting "app cannot run on your PC. Contact the publisher....".
...
Hi. I managed to set up a mesh (Thread) using 9 nodes of the nRF52840 SoCs. I am currently using Putty to send commands and pings between the nodes. What i need now is a way...
Hello, another question from me :) First of all, I'm working with Eclipse, GCC compiler and SDK 15.2.0. I want to add GPIOTE funtionality to the TWI example of Nordic. I'm...
