Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
At the bottom of page 15 in nRF52832 Product Specification v1.4 the following reference is printed:
[1] See GPIO located near the radio on page 17 for more information....
Hi,
If event is not handled (or handled but EVENT register not cleared), will it go above 1 or is it binary?
In other words, can the value be used to detected missed...
I am attempting to port code from sdk 11 to 15. Some of the code is __older__ and in need of updating. A line which runs during the application init calls the sd_ble_version_get...
Hi!
I have added programs for register writing to SPI programs and using SDK14.0.0
I am using the nrf_drv_spi_transfer function to transfer three data.
but when confirming...
Hi,
I am using nRF5_SDK_15.2.0_9412b96 and Segger IDE.
I have written to echo every data received from UART.
I have a variable UART_Data to store data received from...
Hi,
I am using nRF5_SDK_15.2.0_9412b96 and Segger IDE.
I have written to echo every data received from UART.
I have a variable UART_Data to store data received from...
Hi!!
I am now using SDK 14.0.0. and I have added UART functionality to the SPI program().
I could confirmed that SPI and UART can transmit data separately.
However,...
Hello,
I am trying to modify the ble_app_uart code so that my peripheral can send data automatically to the central, which in turn can print it on a computer through UART...
My application is a BLE peripheral and will only allow a single connection to a BLE central. Hardware will be nRF52832. My test application was based on a Nordic example that...
Hello,
I am working on Bluetooth Mesh authentication. I wonder if you have more details about Input OOB . I am trying to input a number from nRF Mesh app to send it to the...
I need to confirm before buying, whether the nRF52840 chip and the nRF52840 development board can be used to develop a Zigbee Mesh.
Also whether "nRF5 SDK for Thread and...
I need to do pairing between the two 51822 modules. All the information I find is paired with the slave and the mobile phone. There is no host matching process demo or learning...
Hi
I'd like to create a firmware that supports multiple Nordic boards as Hardware (as the nRFConnect Firmware does). To do that I have to configure the peripherals according...
Hi,
I am trying to test an application running on the nRF52840 using your nRF Sniffer (actual version 2.0.0.2.beta).
My application should be able to request a change...
