Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
I feel defeated. Programming nrf52 uses libraries that rely on libraries that rely on libraries and on. Loading a new project into Segger Embedded Studio loads none of the...
I have a very simple problem - using nrf52832 sdk 14.1.0 I cannot connect to iphone (7 or greater) and HTC (android 7) with the same value of NRF_SDH_BLE_GAP_EVENT_LENGTH...
Hey Guys, I am trying to program my nrf52832 board by connecting it with J-LINK(EDU) but could not do it. JFlash was giving failed to connect error. Even NRFGO Studio was...
Where could I find the nRF Connect v2.6.1 for desktop documentation? And more precisely, the one describing the Programmer official v1.0.0 functionality? As far, the only...
Hi,
I'm trying to get the scanning procedure to work while my device is connected to a phone. At the moment, even though I start the scanning procedure, I don't get any...
Hi,
I am using NRF52832 SOC for my application. I have developed application for beacon advertisement based on the nrf sdk. I am facing some issue in device advertisement...
I want create a simple application such that when I send a string "Hello" from the nRF UART Android app to the board, I receive a string "Hi" back to the phone. How do I write...
Hi,
I’m developing a BLE remote control device (S132 softdevice && SDK 15.2.0) . It works with NRF52832 programmed as a central BLE (I started from ble_app_blinky (central...
Hello, i am having problems with a loop in the function "flash_manager_wait()"; in the begining of the code.
main()-> initialize()-> mesh_init()-> mesh_stack_init(&init_params...
Hello, I have a discovery issue that seemingly only happens with the Samsung Galaxy S8.
I want to throughput test BLE5.0(2Mbps).
I using the nRF52832(BMD-300) with SoftDevice...
Hi!!
I'm adding spi functionality to S132 and SDK 14.0.0 ble_app_uart now.
The communication which added the function of UART to SPI and the sample code of ble_app_uart...
hello,
Now, i want to recover MAC from static random state.
for example, if MAC[5] =0X55 in chip itself, The MAC in adv in 0x1101 0101 ;
but i want mac in adv is 0x55...
I am using nRF52 SDK v15.2.0, nRF SDK Mesh 3.0.0, and Segger v4.1.2.
I keep getting Mesh Error 6 while trying to combine the provisioner role with the client model. Which...
Hi,
I'm using nrf51822 with a custom board, where I should turn on a buzzer sometimes. I configure a timer and ppi to make a bip alarm. each bip lasts about 1sec; and the...
