Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hello development zone,
I'm new to nordic, and I have a question about role swithcing.
With knowing that, this kind of questions may be answered many times before only in...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
hello everyone
I have some questions with the following function in the hal_aci_tl.cpp file
static bool m_aci_spi_transfer(hal_aci_data_t * data_to_send, hal_aci_data_t...
Throughout twi_hw_master.c, there are lots of places where the code directly accesses PPI channel #0 and thus assumes it's available, as in:
NRF_PPI->CH[0].TEP = (uint32_t...
Hello, I have built a couple of custom boards in the past using the nRF51822 and have stuck very closely to the reference designs. They have all worked.
In my latest board...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hello,
I successfully flashed the experimental_ble_app_uart, I just modified it to do an echo (when I send something with my phone uart app, it give me back the same value...
Since related topic Is BLE changing licensing policy? was marked as resolved I moved my question to new one.
My company is ready to get SIG membership for BLE usage and pay...
I'm creating a custom beacon, similar to iBeacon, but with a custom data format. It advertises only once every 8 seconds, but the iPhone app doesn't receive advertisements...
I tried to read out the temperature sensor of NRF51822. In light CPU load (turn on ADC and send data through BLE every 1s), the measured value is around 45 degC, compared...
I am using the RTC1 compare event to generate a periodic interrupt. When I halt the bugger and and then run the interrupt doesn't occur. Looking at the RTC1 register set shows...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I am working on a system where two nRF51 will communicate with use of the ANT protocol (S210). The master and slave must be paired after pressing a button on both sides. I...
