Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
Im using SDK11 and id like to use serial DFU, when i try to run pc-nrfutil I get a message "Serial transport is currently not supported".
Id like to write own update...
Hi,
I just upgraded to the new SDK (12.1) from SDK 11... and I'm completely lost about the new secure DFU... Previously I correctly implemented a buttonless DFU in my application...
Hi,
I make some tests on power consumption of nRF52 with evaluation board and I remark some peak on the current. it's appeared that this peak is generate by DEC4 output ...
Hi, if i pair my nrf51-dk with my iPhone works, than I pres discontent (bluetooth settings),
now,
if I try whit another iPhone this doesn't work...
If I reset the board...
Hi,
I think there's an error in SDK12's nrf_drv_uart, some code parts unconditionally use p_instance->reg.p_uart (eg. nrf_drv_uart_task_address_get, interrupts_enable)...
Hi
Recently in the release notes of the SDK12 I noticed a line about updated the MDK update:
Included a critical MDK update (v8.7.1)
My SES project uses the...
Hi,
Is there an example available for Nrf51822 BLE HID (nrf5 SDK v11) with Feature and Output reports?
I've added an output HID report to HID mouse example from SDK and...
Hello.
I use nRF52 and tried to make the shared channel.
There are 1 Master and 1 ~ 3 Slave device.
When the master device send the notification messages to slave...
Hi,
I just did a quick diff using these two commands
> find nRF5_SDK_12.0.0_12f24da/ -type f | grep --text -v -e "c$" -e "h$" -e "s$" | sed 's/.*\///' | sort -u > exclude_list...
Hi
we are switching from NRF51 to NRF52.
Putting the same (very basic) inits for sd and advertising, leads to NRF_ERROR_INVALID_PARAM..
This is my source:
#define...
Hi,
I downloaded the latest SDK V12, coped the example HEX from the BLE Beacon and it worked fine.
I tried to then compile using Keil, it compiled, but I noticed that in...
Hello,
I am currently using the TWIS (slave!) peripheral to get data from a I2C master. Now I would like the ability to place the nRF52 in deep sleep mode with sd_power_system_off...
i am using UART service for implementing BLE App on iPhone-4s by using objective-c.
i downloaded old source code of UART but it can't work.
so can i get latest updated UART...
Hello Everyone,
I am working on nRF51 can any one tell me how can i get current time in microsecond?
micros() return current microsecond time in arduino. I wants same...
