Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi,
I'm using nRF5_SDK_12.2.0_f012efa and s132_nrf52_3.0.0_softdevice. We want to do the OTA on it. However, I found that there is no DFU service in the HRS example.If...
Hello,
I am using the uart example with modifications to add SAADC and TWIS. It woked well for a while but now it does not connect properly to my iPhone. I reverted to the...
I am developing Timeslot program with FreeRTOS. (on nRF51822)
timeslot's signal handler is
timeslot_signal_callback()
...
xQueueSendFromISR(s_timeslot_queue, &cmd, NULL...
BT 5.0 mention that:
Up to 8x the broadcasting message capacity over Bluetooth 4.2, with
support for larger data packets: 31-octet to 255-octet packages.
Do you have...
Hello,
Brand new bluetooth 5 standard allows to create data packets up to 255 octets.
So, does maximum size of advertising data in Nordic devices comaptible to bluetooth...
Hello, when using sd_ble_gatts_hvx(), I keep getting 0x3401 error. I googled it and it appears that it's because I might not have the notification enabled.
But I very much...
OK. Weird question. I know, but that's only because I'm in the middle of a large program that I'm reading, believe me, I had done my fair share of homework and I understand...
I can't seem to get any of the UART examples for the NRF52 to compile on Eclipse. Eclipse is complaining that there are two definitions for uint8_t, one in _stdint.h and another...
Dear developers,
Currently, I am studying the new SDK 12.2. Now, I'm reading flash storage module. It seems very useful.
Just a question: While Persistent Storage module...
So it points to the ACTUAL value of a characteristic. So why do we need that function "ble_hvx_push()" (forgot its name, sorry, but you know what I mean) for? And what's with...
hi dear Engineers!
if I use sd_ble_gattc_primary_services_discover(..) with NULL last parameter , all SERVICES discovered OK:
start_handle=0x0001;
err_code = sd_ble_gattc_primary_services_discover...
We have a device which needs to survive dishwasher conditions. We believe most dishwashers operate up to 71C, but may reach 82C during 'sanitation' phase/drying.
This is...
Hi,
I'm using nRF5_SDK_12.2.0_f012efa and s132_nrf52_3.0.0_softdevice. We want to do the OTA on it. Before I add a DFU service to make it switch to bootloader, I have use...
Hello, I'm sending a series of data up to 7 bytes from an android phone, but I can only receive the first 5.
I'm asking what are the list of thing to mind if I were trying...
