Hello,
I'm trying to make the nrf5340-DK capable of connecting to BLE from multiple devices.
The program is based on: Bluetooth: Bluetooth: Peripheral UART .
I found...
Hi all,
I'm trying to use rtc0 with my custom board build with an nrf9151, but I got a secure fault. I've activated rtc in an overlay file
In my prj.conf
But...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
In order to reduce power consumption , I configured the RX pin of the serial port with an interrupt , and when the device was asleep , it was woken up by an interrupt , and...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
i've noticed that the pc-nrfconnect-ppk is written in typescript (with a lot of .tsx files for visual elements)....
my understanding is that at the lowest-level the power...
Hi, I need help for generating the init packet. I'm using SDK 11.0.0 , s130 on nrf51822. To build bootloader, I've used the sample bootloader with some include path changes...
I try to print the RSSI level but i couldn't do.
I use nRF51 DK and soft device S130.
This is the line that i just write:
SEGGER_RTT_printf("RSSI: %d\n",p_gap_evt-...
I'm trying to create a project from scratch that can use the S132 Softdevice, but I am constantly running into problems trying to get the correct headers, preprocessor macros...
Hello Nordic,
I am using the BL600 third-party module and SDK 10.
I was able to modify and compile project with GCC at
examples\ble_peripheral\ble_app_uart\ for s110...
As title,
I found that on the official website,
and I think it's extremely useful for someone(me) who need to measure the power consumption(current).
I can't find...
When I operate RESET PIN in main function like this:NRF_POWER->RESET = 1,Then cause a HardFault_Handler, (/attachment/fabd1141d36157d32f8c0353e4880b3e),What's this？
hi NORDIC,
is it possible to store float array in fds. i am able to store intrger values but unable to store float values. i am using example in this link :- github.com...
We have observed in couple of large size deployments that data packets from beacons that are bit far away tend to be corrupted. Devices that scan the signals from BLE beacons...
I have read the previous questions regarding the above subject, i found that changing the maximum bonding devices limit defined in device_manager_cnfg.h will work, but it...
Hello everyone, I must to write and read a I2C eeprom like 24c256. I tryed to do it but all the examples with I2C protocol works with 8bit addressing. I tryed to modify mpu6050...
Does the components on the development kit increase the power consumption compared to what you would expect from a low power-optimized application-specific PCB?
Other than...
I use the ble uart app to receive the data from mobile phone. The data packet size is 20 byte. If I transmit the packet one by one without adding delay, is it possible that...
HI,
Can anybody give me the connections to a BMD-300 with nRF52DK and the steps to program a BMD-300 from scratch? Which document provides the information, if there is any...
For ble_app_uart, if I write below routine to send data to mobile phone application. Can the mobile phone application receive all the packets without packet lose.
for(i...
