Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi
I'm trying to catch the GPIOTE_IRQn interrupt, while the device is in system off.
Not enabling the SD130 V2 the interrrupt is caught once, and then not anymore...
...
Hello,
I'm currently trying to pair my board with my phone and I've faced some issues.
After downloading my device(NRF52 PAC10040 board) with experimental_ble_app_blinky...
Hi all Nordic developers,
I am currently working on nrf51 to scan all the nearby beacon and then i wish to send the data to the esp8266. I already able to scan all the...
When I try to copy a zip file from my email to NRFToolbox for DFU, the NRFToolbox app comes up and then immediately crashes.
Steps to reproduce:
Download latest NRFToolbox...
Hello, as it is clearly understood (by everyone developing using NordSemi's SOCs), this struct "ble_evt_t"
Hello, as it is clearly understood (by everyone developing using...
Hi,
I've read in your press release for SDK 12 that increasing the MTU beyond 23 bytes is now possible on the nRF52. I thought I'd test this increase out on my nRF52 with...
Hi All,
I have a basic question, i want to know what are the right value to use with the nrf51422 chip for the resistors with ADC.
I want to use the maximum value permitted...
Hi, I have problem with using example codes. I want to add GPIO control to ble_app_uart example. Adding gpio_config() function taken from app_timer_tutorial blocks program...
I'm using NRF52832 SoC and IAR
I've to read data from ADC using SPI. ADC will generate interrupt every 4ms indicating data ready. I've configured GPIOTE to sense the ADC...
A couple of power consumptions Q's for this basic scenario: RTC used via PPI to infrequently sample from ADC and trigger SPI read from external sensor source.
Questions...
Hello,
I need a support for BMD-300 BLE module.
We can flash the BLE module and we can connect it with mobile application via Blue-Tooth.
But when we flash BLE for...
Hi,
I'm using nRF51822 in my senior project (some kind of BLE wearable device).
I'm trying to call my function inside the ble_evt_dispatch() function but it doesn't...
SPI Slave configuration On nRF52
Hi,
I am trying to configure the SPI slave peripheral for interrupt based communicaton with a SPI master
In previous work with ARM...
