According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi,
I am developing an app using the base module "ble_app_uart". In our application we would like to store data in the flash memory.
I am using "Flash Data Storage"...
I want to make my nRF52 turn on every 5 minutes, send data to a device over BLE and go back to sleep. For some reason once I turn on BLE advertising LED1 becomes solid and...
Dear Nordic Team,
Thanks for supporting.
We are worked in nRF51422 development kit.How can i enable DFU service in all BLE APP examples source codes in main.c
Please...
Hi,
when I use nRF Connect (or MCP before) to browse my BLE service, I get shown some garbage if I use many characteristics in my service.
When I use 45 characteristics...
Hello people,
I'd like to use the NRF52832 (QFAAB0) / PCA 10040 / S132 development board as a data logger. For that I soldered a micro-sd card reader and started using...
I set the connection as follows:
#define MIN_CONNECTION_INTERVAL (uint16_t) MSEC_TO_UNITS(500, UNIT_1_25_MS)
#define MAX_CONNECTION_INTERVAL (uint16_t) MSEC_TO_UNITS(1000...
I am trying to use the mesh network using the nrf51822. I have to use the app_timer with my application. Mesh library and the app_timer library making conflict with the SWI0...
I was trying out the low power PWM example and noticed the timing inaccuracy that was mentioned in documentation .
For example, with low_power_pwm_0,
period = 220...
I have checked the datasheet between 51422 and 51822,they look the same,but why the NRF51422 can flash BLE and ANT+,but 51822 can't? Is the Radio part different,or the Flash...
I have based my firmware on the Proximity Application example.
Now I need to extend my application to support BLE DFU service.
But as i read Extending your application...
Hi,
I am using the flash memory for a few variables and it works very well. Now I have one flag which is defined by #define statement and if it is enable then the initial...
hi,
i have nrf8122 module . want to flash a hex file in it by using nrf51 development kit. is it possible to flash code in the nrf51822 module. other wise please provide...
Hello everybody,
I'm working in a project & need to listen for notification from installed applications in the mobile phone & update the mobile app with some info about...
I have combined Nordic's serial connectivity code and Nordic's serial DFU example.
Upon initial powerup, the nRF51822 draws an expected amount of current (~600uA). When...
