I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Hello,
with Android 5.0 BLE central and S110 8.0 peripheral I do this:
Erase all bonds in device_manager_peripheral.c
Check that m_peer_table contains zero...
Hi,
I would like to convert a blinky project for the BOARD_PCA10040 to my own custom board. I can't find on eclipse where "#define BOARD_PCA10040" symbol is defined so I...
Hi,
I'm trying to config my device with resolvable private addr (RPA) as code below:
rpa_add.addr_type=BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE;
sd_ble_gap_address_set...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Dear Nordic Developer Zone,
In order to synchronize some tasks (motor-driving), I have recently implemented the radio notification interrupt.
In this interrupt, I toggle...
Hi,
After following all instructions on: gnuarmeclipse.github.io/.../
And after installing all Nordic Semi dependencies on eclipse.
I import on eclipse the UART_Loopback...
I'm trying to interface the twi driver with a ft200xd chip (i2c -> USB serial). I want to read the available bytes, but it requires a general call first see page 29 of www...
Hello everyone!
I got one question and could you guys help me out?
When I open the nRF Connect Mesh, after I program successfully, I can't initialize selected device while...
Hi, I'm working on a cross-platform application that needs to communicate with a custom peripheral (nRF51822 with S130 v2.0.1). I've implemented the interface for both Linux...
Long time reader first time poster upper.
I am working on a very minimal BLE send / receive scheme for a research project, and am not using a SoftDevice. I have written...
Hello,
I am noticing something curious when I attempt beacon mode for my nRF52 (sdk 12.1). Attached is an image of ubertooth packets that correctly show my ADV_NONCONN_IND...
Hi,
I am trying to communicate to PCA10040 (nRF52) dev board to communicate.
Basically i want to configure 1 board as Master another as slave, so master will initiate...
Hi,
I am using SDK 11.0 for my project development. When I tried to compile the unaltered SPI example given I got 60 Errors in my laptop. The Same SDK in other laptop is...
Hi all,
first of all I'm new to NRF and BLE applications so I'm truly sorry if some of my questions are very basic and if answer to some of them is already posted somewhere...
Hi all,
I am using pins P0.00, p0.01, p0.09 and p0.10 in my application. I wandering why these pins are not functioning as GPIO. I have searched various links such as ...
