Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello, after I program bootloader, sd, application, I did the following command to do read back protection,
nrfjprog --rbp ALL -f NRF51
But, even though I still can...
Is there a way to achieve what bsp_event_to_button_action_assign(button_id, action, event) does but using my own button?
The functions requires a button_id like 0,1,2,3...
When I use NRF_LOG_GETCHAR() witn nRF52 DK and onboard SEGGER UART it stops in next NRF_LOG_INFO(). Also after ARM reset it keeps in this error state. It seems that SEGGER...
Hello,
I'm trying to install wireshark sniffer on ubuntu 14.04 with PCA10031.
I follow this guide : devzone.nordicsemi.com/.../
But when I launch sudo python example_linux...
Hi,
I am trying to replicate the "Throughput and long range demo" from devzone.nordicsemi.com/.../
I have two nRF52840 boards. I am using IAR studio. I can compile,...
Hi,
i am working on TWI sensor example in SDK1. in which i connected SCL And SDA pins tonRF52 dk boards sca and scl pins. and connected voltage and ground. when i run the...
Hi everyone,
I am using the nRF52832 and I have use the serial bootloader to update the firmware at one of my clients place.
How should it be done and what do I have to...
Hi guys,
I want to implement the periodical transmit over the mesh network. I have 3 nRF52832 DK, and I use the nRF OpenMesh example.
What would be the best way to implement...
It appears this example hangs after the following call. Does the experimental 12.2 buttonless DFU work ok?
SOFTDEVICE_HANDLER_INIT(&clock_lf_cfg, NULL);
Using SDK 12.2 and BDS plugin version 1.2.2
Module nrf52832_xxaa
Copied plugin output to nRF5_SDK_12.2.0/examples/ble_peripheral/experimental_bluetoothds_template/...
I have observed that the "Experimental Buttonless DFU Service" and its characteristics has the same UUID. But in case of other services(like battery service) the UUID for...
I know that the pairing popup won't be shown if encryption is disabled.
I was able to remove the popup on Android. However, I couldn't find a way to do it on iOS.
The...
Hi there,
I have multiple PCA10040 boards, and about a year's worth of experience developing code for them. I have suddenly started to have problems with USB-UART connections...
Greetings,
I have a setup where I have a periodic single channel low power SAADC implementation. In this the configuration is
A single SAADC channel is initialized...
Dear Nordic,
After playing around (a lot) with your nRF51 and (all) of your nRF52 devices, both on a personal and a professional level, I would find very interesting to...
