Hey everyone,
I have designed a custom board with a bunch of nordic IC's (nRF54L15, nRF9151, nRF7002 & nPM1300)
I have tested the basic functionality so far, including...
I have set up the OTBR with a RPi 5 and an nRF 52840 DK as an RCP. The CLI device can join the thread network as a child, the OTBR as the leader.( https://www.youtube.com...
How can I display the nrf serial terminal logs files on VS Code while keeping the same colors and text highlights for dbg , inf , wrn , etc., just like when viewing live logs...
Hi,
I am trying to build bluetooth hci_uart sample for esp32 board and haven't had much success so far. I am running this command to build:
`west build -p always -b...
I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Dears,
I am developing a ANCS application with nus service on our product. There are a few problems I don't know how to fix it.
My problem is that :
1. ANCS will not disconnect...
Hey guys,
I have designed one custom PCB based on BMD301 in which I am observing some weird behavior on RESET pin. I have connected reset pin of BMD301 i.e. P0.21 to 3...
How do I deny a connection if the connection is unencrypted? I'm currently trying to do it with the peer_manager using
case PM_EVT_CONN_SEC_FAILED:
{
/** In some cases...
I have request similar to this questions but for SDK13:
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
Judging by quick grep sdk_config.h from ble_app_template...
I am having some trouble getting the Power Profiler to start up correctly. Currently, I have the PPK DK plugged onto the PCA10040 DK. All of the onboard switches are set to...
Is there someone I can contact about acquiring some sample chips for prototyping? The normal distributors don't seem to have any information regarding the engineering samples...
Hello,
I am currently working on a project involving the nRF52DK to be a central device.
The peripheral device is based on the Nordic Uart service with minor changes...
hi，
i tried add ancs to the s130 ble_app_hrs_rscs_relay demo， when i use iphone5s to connect， the uart display as follow，but when i receive a message or a call， the software...
In GATT Packet transfer, is there occurs any packet loss and retrial?
I'm trying to connect about -90 Rssi dBm peripheral device with my nRF51-dk.
In this far range...
Hello,
when I was working on MSP430 I used to place the firmware version constant at a known address in flash so that it can be verified which firmware version is flashed...
I was having some troubles using the app_timer (RTC1) shortly after mesh startup, so I enabled the PIN_IN_CB and PIN_IN_TS debug pins, and saw some interesting behavior. ...
Hello all,
am trying to configure 3 adc channels in a way to have conversion in 3 differents pins, without usin timer and ppi. so I implement the following code, the problem...
Hi
May i know what would be the debugging procedure using segger-RTT for nrf52840 and what is the debugging Hardware Required ?
Thanks and Regards,
R Madhu.
I know BLE5 is the future of IoT. I also want to invest on it.
But how to setup a complete BLE5 environment? In China, IPv6 has not been supported. Therefore, 6LowPAN/Thread...
