Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi there,
I am getting some error in my SAADC measurements and I believe it's due to the R_INPUT forming a parallel resistance with my voltage divider at the input (the...
Hi,
I am measuring the current during sleep, after the sequence, __WFE();__SEV();__WFE();.
With NRF_LOG_ENABLED set to 1, the current is about 486 uA. With NRF_LOG_ENABLED...
Using: nrf51822, SDK 10.
My application needs to use TWI0 and SPIS1 at the same time. However if I enable TWI0 and then SPIS1, when I run nrf_drv_spis_init() I get NRF_ERROR_INVALID_STATE...
I am working with the SDK 13 ble_app_att_mtu_throughput example. With the SDK 12 example, it seems to require the SoftDevice to be loaded with the arm5_no_packs example. The...
Hello,
I'm designing a project with the nRF52832 where I will use an external SPI ADC.
For debug and backward compatibility purposes, I also plan to use the SAADC.
The...
in the ble multilink central example i'm not understanding where the functions in client_handling.c are exercised some don't seem to be used in main or client_handling (client_handling_dm_event_handler...
I am reporting a problem that might bite you. A Waveshare NRF51822 module comes with a "Passed" sticker on the back (solder side) that makes the module stand off the mother...
Hi,
We are trying to have a thin beacon design. But we are having difficulty in finding low profile inductor for dc-dc converter matching the recommended value of 10uH...
I'd like to use Logic Analyzer in uVision 5.2 and ulink2 for analyzing variables in nrf52832.
In my understanding, I need to use SWO and configure Trace setting properly...
Hi,
I need to capture a demodulated, manchester encoded signal (16 bits long). The data rate is about 50kHz (give or take). Currently, I am configuring a PPI with timer1...
Hello,
I'm using nRF52840 which is surpport Bluetooth 5. I couldn't understand why it can do 8 X range and 2 X data rate than Bluetooth 4.2.
Besides, how to use Bluetooth...
I observe strange behavior while reading value for long characteristics.
I have characteristic 100 bytes long (read only).
In GATT client I must read value with subsequent...
can i get nrf 51 beacon antenna printed on beacon kit. its semicircular in shape... can any one help me
i want eagle library of the antenna
please help
