I am getting an error of "undefined reference to `pm_state_force" .
Also, the output files, config file is not showing the command : CONFIG_PM =y
prj.conf file has : ...
Hello,
We have the custom board with nRF54H20. The VDD_EXT pin is used to power some GPIO ports of nRF54H20 (P1/P2/P7).
The voltage we see on VDD_EXT is about 1.3V instead...
Hi,
I want to test the behavior of Enhanced Multi-Admin added in Matter 1.4.
Is it possible to verify this behavior using a Nordic DK board, sample code and a Raspberrypi...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hey I am a beginner and I want to use mpu-6050 interrupts to sample the sensor values. I am able to read and write values through i2c but I want to read values only when any...
Hi, I'm updating my code which used to have a direct handler GPIOTE_IRQHandler(void), however I can't seem to get this working.
The Kiel Run Time Management has a requirement...
I updated from SDK 8.0 to SDK 8.1. My project had both app_uart and app_gpiote. With 8.1 (I don't exactly remember how it was on 8.0 and I have not spent any time researching...
I wanna use a nrf51822 dongle to sniff all data packets sent by 4 to 6 beacons, without large loss. The code I use is a python api given here learn.adafruit.com/.../python...
I need to provide a battery level in the application I'm working on. This application's services will all be custom - I'm not using predefined BLE services.
Our device...
Dear Sirs,
I am currently developing a project using nrf51422. My programs works fine with pca10026 develop board.
I builded a custum PCB for my project. All HW components...
In the ble_app_hrs_c the scanning indication LED blinks with a periodicity of about 4 seconds, while the advertising LED on the peripheral blinks at the expected 2. Both systems...
Hi,
I am currently experiencing TWI module lock-up issues with the hardware TWI library, which is supposedly fixed according to PAN v3.0, issue #56. (The issue was previously...
Hello,
For me, at the moment there are two things unclear.
With the help of some Nordic examples, I was able to add a Service with 3 characteristics to the used S120 BLE...
Hello all,
I'm new to embedded development and could use some help here.
I am currently working on our own board with a nRF51822 chip on it and using SEGGER j-link to...
Hi,
I just got my nrf51 dk and my task is to connect it with a bluetooth device, say a bluetooth treadmill, and retrieve data from it. The bluetooth treadmill was designed...
hi, i'm trying to develop a wearable health device.
actually, the device is a little unusual because it is attached to the Armpit or sole of the foot or inside knee ..
...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello
I'm trying to diagnose a problem I have with my own hand-soldered nRF51822-QFAA based bluetooth proximity device. I have the PCA10028 development kit to compare with...