Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
Good afternoon we are updating some Nordic chips but to make the connection work it is necessary to install the modem version 1.3.1 wait for it to connect and then install...
Hi,
I have a custom board with nrf51822QFAA(256K flash) and I'm trying to test DFU-OTA (BLE transport) for an application. With only Softdevice and bootloader installed...
Hello,
I am developing using nRF51822 Beacon Source code and Beacon Hardware by Nordic.
I want to modify as below.
It never advertise by Intervel Time.
It advertise...
Hi,
I am developing a peripheral Glucose device.
I need to test my product but i dont have a central device or code.
Can you please help us with the central code for...
Hello ,
I am doing a new Keil project to run concurrently ANT for messagging exchange and Bluetooth LE for advertising.
On KEIL pack Installer I cannot find the example...
I want to implement the OTA update in nRF51822 on my custom board. I am using the bootloader example in the dfu folder for this. When I try this code on the DK, it works fine...
I am using nrf51822 with PCA 10001, SoftDevice S110 8.0.1. I try to compile the example "ble_app_proximity_s110_pca10028" and after I made a connection the device disconnects...
Has anybody had any experience in programming an nRF beacon kit over the air using the built-in Bluetooth Smart interface in a Windoze 8 laptop? (HP 255 G3) Is this even possible...
Hi,
I wanted to create fixed rate waveform. I first used nrf_delay_us with nrf_gpio_pin_toggle. But I realized it is not accurate enough to do it, especially when the device...
Hello,
I'd like to know how exactly do i implement this function in my app?
I tried getting the value from response (as shown in documentation) : ble_gattc_evt_char_val_by_uuid_read_rsp_t...
Hi,
My Jlink lite CortexM work with nrf51822 DK boards. But my PCB with nrf51822_xxAA chip can't download code. I'm using ukeil
When I chek in utilities Jlink can't recognize...
I am initializing an SPI master to talk to ADXL362 accelerometer using NRF51-DK.
Datasheet page 19: www.analog.com/.../ADXL362.pdf
No matter what I do connected or disconnected...
Hello,
I am new to working with imbedded chips and could use some help. I am working with a pre-programed nRF51822 chip on a PCB and would like to be able to read the imbedded...
Hi I want to using nRF51822 link with MCU ti-am335x have Linux system(Ubuntu) by standard HCI command, BlueZ or related hci tool.
I know that I can use nRF51822 S120 serialization...
