void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I have my radio chip set up so that it pairs with an iOS device via an encrypted bluetooth connection. Everything works great -- however I'd like to be able to "unpair" from...
Hi,
we are using the chip nRF51822 CEAAE00.
We want to use the pin 0 as output. It is configured as below
NRF_GPIO->PIN_CNF[0] = (GPIO_PIN_CNF_SENSE_Disabled << GPIO_PIN_CNF_SENSE_Pos...
Hi,
I using nRF51822, S110 and NUS to send the data to the phone.
When sending the data, I using ble_nus_string_send function.
I need the execute time to the phone...
When scanning for peripherals using the Master Control Panel Android app, most of the various BLE devices scattered around me show up with a "connect" button next to them...
I have a development board with the AC variant, but for my custom board I have an AB. I am able to flash code using Keil to the development board, but when I change the device...
Can anyone suggest an I2C LCD driver for use with the nrF51822? We will likely be driving a 96-segment LCD but a dot matrix LCD may be an option.
The application is for...
I get the following error on doing OTA DFU using an Iphone with IOS V8.4.
Created .zip files using nrf.exe
Commands used
nrf dfu genpkg --application...
Hi everyone,
We're working with nFR8002 devices, and it works fine most of the time.
Even after losing the link intentionnally (Bluetooth stopped, or walking out of Bluetooth...
This question devzone.nordicsemi.com/.../ appears to show that S132 expects the FPU to be available and activated.
Does the S132 really need/use the FPU or is this an artefact...
Hi,
I know that when advertising in non-connectable mode, the fastest advertising interval is 100ms. I have some questions about this:
Is there any document explaining...
I have been using NRF51822 for some time as BLE chip with services.
For some debugging reasons I need a faster stream method...
I looked at Gazell and found it simple to...
Hi, I have a question about this memory layout .
At Figure 2 (of the memory layout), it erases the previous application.
After that, at step 1, it says that the firmware...
