i have PMIC(I2C based )Max20360 that is developed using twi sensor , to this when i am intergrating a SAADC part throws error error # 134 :expected a field name . 1)why am...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello,
I’m having an issue with my setup: I have a nRF9160 running the bt/peripheral sample through a nRF52840 (running the hci_lpuart sample). It seems to work fine with...
Hello,
I am using nrf52840 MCU.
I am developing a product which have 2 I2C and 2 SPI interfaces. All the interfaces are on different pins.
I developed this thing with...
The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Hi,
I have downloaded "mastercontrolpanel.3.7.1.8567.x86.msi" and try to install on windows xp of my intel core2 laptap. But it failed with prompt like "not a valid windows...
This question devzone.nordicsemi.com/.../ reports the fact that the driver cannot be used twice without manually pin reseting teh BLE dongle.
But there is another problem...
Hi Team,
I am using nRF51 DK as packet sniffer to sniff packets between Mobile and other device.
Why it captures only advertising related packets?
After successful connection...
Hi there,
If I try to store a global variable in flash I can't store it. But when I declare this variable in the main function I can store it in flash. Can someone tell...
Hello all,
I saw their was a new update for the nRF518-SDK and I was wondering how I should update this in Keil. Is this just a simple replace folder? Replacing:
...
I inherited an ANT/BLE nRF51422 project a couple of weeks ago.
It used SDK v6.1.0 and S310 SoftDevice v1.0.0
At the time, I'm sure that the SoftDevice download said...
I'm attempting to troubleshoot problems between dev teams. One team is having some issues & I notice that their binary is slightly larger when built from exactly the same...
I am trying to use the laird BL620 module not for the smartBasic, but to run my own firmware.
I have just set it up, connected to my old segger JLink debugger.
In Keil I...
Press the Connect button on the Smart ponaep NRF Uart V2.0 recognizes the page reongil signal
Disconnect state, allow to boil for your smartphone to wait about 20 minutes...
I am pretty new to the nRF51822 in the firmware side. I have been doing hardware design for many years but need a little help getting started with firmware.
Does anyone...
When the bootloader in SDK 8.0.0 checks whether the application is valid, it only computes the CRC for the application if the CRC in the bootloader settings for that bank...
Hi,
I try to make characteristic broadcasting through advertisement data packets.
Added these codes below, but no yet work. Is there any example for this work ?
char_md...
SDK v8 release notes specifically state that there is no S310 support. Are there plans to support the S310 soft device in future SDK releases or are you discontinuing the...
Hi,
I do some test for nrf51822 power consumption.result as below:
my board
1.system off mode:270uA
2.system on sleep mode(no UART,no GPIOTE):300uA
3.system on sleep...
